Playback does not start.

0The programme has reached its ending portion.

Press ON SCREEN to confirm. [ P39]

0The recording has just completed.

Wait approximately 30 seconds, then press PLAY.

0It may not be possible to record, play, edit, or dub discs recorded or formatted on other players or computers, on this unit.

In addition, noise may appear on the screen or the sound may be distorted.

There is no sound from the coaxial output when performing 1.5x speed playback on the HDD.

To output sound from the coaxial digital sound output terminal on the rear of this unit, check the following setting.

Setup Menu ADIGITAL AUDIO OUTB = APCM ONLYB

[ P98] D

The main and sub audio cannot be switched when the coaxial digital sound output terminal on the rear of this unit is connected.

For multi-channel programmes recorded on the DVD-RAM or DVD-RW (VR mode) discs, check the following setting when the main audio and sub audio cannot be switched.

Setup Menu ADIGITAL AUDIO OUTB = APCM ONLYB

[ P98] D

After setting, press AUDIO to select the desired audio.

Recording

0The desired programme cannot be recorded.0No images on the TV screen.

The channel does not correspond to that in the receiving area. If you are unable to select the desired channel on this unit, set

the correct channel for the receiving broadcast. [

P25, 36]

Recording cannot be made.

0No disc is loaded.

Or an incompatible disc is loaded.

Load a recordable disc. [ P12]

0The disc loaded is not formatted.

Format the disc so that it can be recorded on this unit.

[ P64]

0A finalised disc is loaded.

Recording cannot be made on finalised discs. [ P65]

0Discs formatted on other players may not be recordable on this unit.

0The disc does not have enough space.

Delete unwanted programmes, or load a new disc. [ P80]

The unit does not turn off after completing timer recording.

The unit will not turn off in the following instances.

0DVD is selected while HDD is timer recording (and vice versa).

0When multiple timer recordings were programmed for different decks.

Timer programming cannot be made.

0

Confirm the contents of the timer programme. May not

 

 

function properly when there is a power failure. [ P56,

Troubleshooting/Appendix

 

57]

0

If timer programming cannot be set or cancelled, wait for

 

 

about 1 minute and then try again.

 

The GUIDE Plus+ system

 

This troubleshooting covers only a few problems. For a

 

complete list, please visit the GUIDE Plus+ system website at

 

www.europe.guideplus.com

 

 

 

The programme listing is not displayed.

 

 

 

 

0

It takes 24 hours to download the programme listing data.

 

 

After checking the connections such as antenna connection,

 

 

set this unit to standby mode.

 

0Confirm that there are no problems with the host station channel.

0After deleting channels with poor reception, perform initial setup again.

The channel does not change when receiving via the external receiver.

The IR blaster (G-LINK) cable is incorrectly connected or placed. Also, check the external receiver’s brand name, etc.

Timer programming cannot be set.

The date and time is not set. [ P35]

The recorded programme ends halfway.

Due to circumstances of the broadcast station, the programme broadcasting time may change but this unit does not automatically change its programmed time accordingly.

Others

A- - : - -Bis displayed on the front display panel.

Displays when power failure occurred. Set the date and time.

The disc remaining space does not increase even though all recorded programmes have been deleted.

The DVD-RAM disc contains data recorded on a computer.

Computer data cannot be deleted on this unit. If the data is unwanted, format the disc on this unit. [ P64]

DVD discs recorded on this unit cannot be played on other players.

0DVD-RAM discs recorded on this unit cannot be played on incompatible DVD players.

0Even finalised discs may not be playable, depending on their recording condition.

EN I 109