
Recording
•Cancel the
[TIMER ] before operation for either DVD or VCR. When finished operating, press [TIMER
] to resume the
If VPS / PDC is “ON”:
•In the
If VPS / PDC is “OFF”:
•In the
Checking, Cancelling, or Correcting the Timer Programming Information
In the following example, No. 5 timer programming overlaps on No. 1 and No. 6 timer programmes. In such a case, you should correct the programme time to clear the overlap.
|
|
|
|
|
|
|
|
|
|
|
| Timer Programming |
|
|
| VCR | DVD |
| |
|
| Date Start | End | CH | DVD | Speed | VPS |
| |
| 1. | 01/01 12:00 | 13:00 | AV3 | VCR | XP | PDC |
| |
| DVD | ON |
| ||||||
| 2. | - - - |
|
|
|
|
|
|
|
| 3. | - - - | Overlap |
|
|
|
| ||
| 4. | - - - | No.1 6 |
|
|
|
|
|
|
| 5. | 01/01 12:30 | 14:00 | P02 | VCR | SP | OFF |
| |
| 6. | 01/01 13:45 | 21:00 | P12 | DVD | SEP | OFF |
| |
| 7. | - - - |
|
|
|
|
|
|
|
| 8. | - - - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Press [TIMER
] so that the
icon disappears from the front panel display.
2 Press [PROG] twice.
Timer programming list will appear.
3 Check the information on the list you will need.
4 To clear the timer programming, select the desired programme using [Cursor U / D], then press [CLEAR].
To correct the timer programming
1)Select the desired programme using [Cursor U / D], then press [ENTER].
2)Correct the timer programming using [Cursor U / D / L / P].
3)Press [ENTER] again.
5 | Press [PROG] to exit. |
6 | Press [TIMER ] to return to the |
|
|
To check the timer programming in progress Press [PROG].
Note
•If a timer recording is proceeding, that programme is highlighted in red. In such a case, you cannot select any other programmes.
•When you check the timer programming in progress by pressing [PROG] during operations of the component (DVD or VCR) which is not currently used for the timer recording, the programme will not be highlighted. In this case, you cannot select other programmings.
To Stop the Timer Recording in Progress
On the front panel of the unit, press [DVD STOP S] to stop the disc recording or [VCR STOP/EJECT S/O] to stop the tape recording.
Note
• [STOP S] on the remote control is not effective.
If the Timer Programming Did Not Complete Correctly
The error number appears on the timer programming list.
Timer Programming |
|
|
| VCR | DVD | ||
|
|
|
|
|
|
|
|
Date | Start | End | CH | DVD | Speed | VPS | |
01/01 | 12:00 | 13:00 | AV3 | VCR | E1 | PDC | |
DVD | ON |
2.- - -
3.- - -
4.- - -
5.- - -
6.- - -
7.- - -
8.- - -
The error programme will be displayed in grey with an asterisk and have an error number.
The error numbers indicate:
•Cannot record because of the NTSC / PAL- 60 signal is received.
E29: Disc protected
E30: Disc full
E31: Already recorded 99 titles (Video mode)
E32: Already recorded 99 titles (VR mode)
E33: Already recorded 999 chapters
E34: No space for Control Information
E35: PCA (Power Calibration Area) full
E36: Already finalised Video format disc E40:•There are some unrecorded parts due the
overlapped timer programmes. •Recording did not start at the start time. •There is no tape in the cassette compartment.
•Tape recording reaches to the tape end during timer recording.