84 EN, Timer Recording | JVC HR-S9850EU guide

84 EN			TROUBLESHOOTING (cont.)
TIMER RECORDING (cont.)
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
6.	“[” on the front display panel and	● The loaded cassette has had its record	Remove the cassette and cover the hole
	SAT # indicator won’t stop blinking.	safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		Automatic Satellite Programme	recorded in its entirety. Next time make
		Recording.	sure you have enough time on the tape to
			record the entire programme.

7.	The power shuts off and “[” won’t	● The end of the tape was reached during	The programme may not have been
	stop blinking.	Instant Timer Recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 74).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

6.	The remote control won’t operate the	● The remote control brand setting is	Re-set the remote control to the correct
	TV or satellite receiver.	incorrect.	brand. ( pg. 40, 41)

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 84

JVC HR-S9850EU specifications 84 EN, Timer Recording

Contents

Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Remote Control How To Use Remote Control LCD Check the contents 10 ENSituate the recorder Connect the recorder to TV 8To connect to a TV with S-VIDEO/AUDIO in connectors Plug the end of the mains power cord into a mains outletVideo Connection Auto Set Up 12 ENTurn on the recorder Select your country Perform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or e Perform Preset Download 14 ENSet the video channel Press rt to select CH - and press OK or e Language for the on-screen display Just Clock Access the Main Menu screen Access the Country Set screenLanguage 16 EN Installing Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connections Setting satellite receivers brand and channel 18 EN TV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 EN Slow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback 22 EN Variable Speed SearchSkip Search Index Search Next Function Memory Repeat PlaybackManual Tracking Soundtrack Selection 24 EN Instant Timer Recording ITR Tape Remaining Time Engage the Record-Pause mode 26 ENRetake Locate the start point Engage the S-VHS ET mode Adjust the audio recording levelSuper VHS ET S-VHS ET Audio Recording Level Control Receiving Stereo and Bilingual Programmes On-screen DisplayReceived Playback Recording Access the Showview display Access the Showview screenAccess the Showview Program screen 30 EN Set the VPS/PDC mode Access the Title Edit screenEngage the recorder’s timer mode Enter the programme title Express Timer Programming 32 EN To Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+ Enter the programme mode Before performing the 24 Hour Express Timer Programming34 EN Set the programme start/stop time and channel You can programme this recorder to timer-record as many as Disengage the timer mode Access the Programme Check screen/displayAccess the Programme screen/display Press # TIMER, then press Cancel or change a programme Return to the timer modeSelect the programme to modify Enter the programme title Programme 4 overlap each other Select the L-2 Select mode Recording modeProgramme Recording 38 EN Remote A/B Code Switching Set the remote control codeCheck the remote control code for the recorder Change the code for the recorder TV Multi-Brand Remote Control 40 ENSet the TV brand code Operate the TV Satellite Receiver Multi-Brand Remote Control Set the satellite receiver brand codeOperate the satellite receiver Navigation 42 ENNavigation Playback Check Memory Turn Off Navigation Video Navigation Title ScreenCheck the memory Turn off Navigation Access the Find Blank Space screen Edit Title44 EN Find Blank Space Access the Edit Title screen Edit Tape TitleEntering Character Select the tape title 46 EN Choice of CategorySelect the programme Select the category Delete Tape Data Delete Programme DataDelete the tape data Delete the programme data Access the Find Title screen Find Title48 EN Sort By Tape Number Access the Tape No. screen Access the Date screenSort By Date Select the programme Access the Category screen 50 ENSort By Category Category you want to watch Set the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorder Access the Output/Input Set screen OUTPUT/INPUT SET, thenPress OK or e Select and L-2 Input Setting Decoder connector Another Video Recorder 54 EN Recorder Player Audio Dubbing 56 ENPre-recorded tape Audio-dubbed tape CD player, etc Engage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-1 Insert Editing 58 ENSource tape Before Insert Editing Recording tape After Insert Editing Engage the Insert Editing mode AV Insert EditingLocate the end point Start Editing Access the R.A.Edit screen 60 ENLoad the source cassette Start playback of the source cassette Memory Capacity Prepare the recording deckStart Random Assemble Editing End Random Assemble Editing 62 EN Start Synchro EditingPause Synchro Editing Press Synchro 7/79 Access the Jlip ID No. Set screen Set the Jlip ID numberJlip ID Number Examples Connecting To a Satellite Receiver Simple Connections Perfect Connections Satellite receiver Decoder Back of recorder Select the input mode 66 ENConnect the decoder Set the tuner Connecting/Using a Stereo System Make connections Mode Set Access the Mode Set screenSelect the mode Select the mode setting You can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is 70 EN For Example About Ntsc Playback Access the Auto Channel Set screen Tuner Set72 EN Auto Channel Set Perform Auto Channel Set View the Confirmation screenPress OK twice 74 EN Manual Channel Set When Receiving a Scrambled Broadcast Delete a Channel 76 EN Set Stations aSet Stations B TV Station And ID List Station Name Access the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 78 EN Showview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program number Access the Clock Set screen Clock Set80 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operation Troubleshooting 82 EN Recording Timer Recording 84 EN Playback 86 EN Auto Set Up Manual Tracking Mode SetAudio Dubbing AV Insert Editing S.T. Picture System International telephone Language code Country code