ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation. | Rear view |
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
•If noise is a problem...
This unit incorporates a noise filter in the power circuit. However, with some vehicles, clicking or other unwanted noise may occur. If this happens, connect the unit’s rear ground terminal to the car’s chassis using shorter and thicker cords, such as copper braiding or gauge wire. If noise still persists, consult your JVC car audio dealer.
•It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 21 of the INSTRUCTIONS).
•The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
A Typical Connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
1
2
3
Connect the colored leads of the power cord in the order specified in the illustration below.
Connect the antenna cord.
Finally connect the wiring harness to the unit.
2
To CD changer or another external component (see diagram 
)
3 | Black |
|
15 A fuse
Line out (see diagram 
)
1 | *1 Not included for this unit. | Ignition switch |
To metallic body or chassis of the car
*2 Before checking the operation of this unit prior
to installation, this lead must be connected, otherwise power cannot be turned on.
Yellow*2 | To a live terminal in the fuse block connecting to the car battery |
| (bypassing the ignition switch) (constant 12 V) |
Red | To an accessory terminal in the fuse block |
| |
Blue | Fuse block |
To the automatic antenna if any (250 mA max.)
Blue with white stripe
To the remote lead of other equipment (200 mA max.)
Orange with white stripe
To car light control switch
White with black stripe | White | Gray with black stripe | Gray | Green with black stripe | Green Purple with black stripe | Purple |
| Left speaker (front) | Right speaker (front) | Left speaker (rear) | Right speaker (rear) | ||
B Connecting the external amplifiers
You can connect an amplifier to upgrade your car stereo system.
•Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
•Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
Remote lead |
Remote lead (Blue with white stripe)
C Connecting the external components
•Set “EXT INPUT” to “CHANGER” (see page 21 of the INSTRUCTIONS).
CD Changer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| *5 Connecting cord supplied for your CD |
CD changer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| changer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CAUTION: | |
jack |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| JVC CD changer |
| • Before connecting the CD changer, make | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| sure the unit is turned off. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To the remote lead of other equipment or automatic antenna if any
Rear speakers
JVC Amplifier
Front speakers
Front speakers
Apple iPod® or JVC D. player
You can connect an iPod or a D. player using an interface adapter (not
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
CD changer jack
Apple iPod (separately purchased)
JVC D. player |
(separately purchased) |
JVC Amplifier
*3 Signal cord (not supplied for this unit)
*4 Firmly attach the ground wire to the metallic body or to the chassis of the
• Set “EXT INPUT” to “EXT INPUT” (see page 21 of the INSTRUCTIONS).
External Component
You can connect an external component using a line input adapter,
External
component
CD changer
jack | External |
component
3.5 mm stereo | *6 Signal cord (not supplied |
mini plug | for this unit) |
| |
|
|
2
