Basic operations
The
–When you select the source (except “TV”) (see right column).
–When you adjust the volume (see page 13).
–When you turn off the sounds temporarily (see page 15).
–When you select the Surround/DSP modes (see page 42). To cancel the function, set “SUPERIMPOSE” to “SUPERIMPOSE: OFF” (see page 25).
1 | 2 | 3 |
| Source lamps |
|
1 |
|
|
2 | When operating the receiver | |
| ||
| using the remote control, set | |
3 | the mode selector to |
|
| “AUDIO/TV/VCR/STB.” |
| |
1 Turn on the power
Press 
STANDBY/ON (or 
AUDIO on the remote control).
The standby lamp goes off and the source lamp of the current
source lights in red.
Current source name appears.
EQ C.TONE | VIRTUAL SB | AUDIO P. BASS | TA | NEWS | INFO RDS | TUNED | ST | AUTO MUTING SLEEP AUTO MODE | |||
LPCM | L | C | R |
| PL |
|
|
|
|
| ATT |
DOLBY D | S . WFR LFE | NEO : 6 |
|
|
|
|
| HP | |||
DTS AAC |
|
| DSP 3D | MHz | |
LS SB RS | |||||
96 / 24 | AUTO SR | kHz | |||
2 Select the source to play
On the front panel:
Turn SOURCE SELECTOR until the source name you want appears on the display.
The source lamp corresponding to the selected source lights in red.
•As you turn SOURCE SELECTOR, the source changes as follows:
EQ C.TONE | VIRTUAL SB AUDIO P. BASS | TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE | ||||||
LPCM | L | C | R |
| PL | ATT | ||
DOLBY D | S . WFR LFE | NEO : 6 | HP | |||||
DTS AAC |
|
|
|
|
| DSP 3D | MHz | |
LS | SB | RS | ||||||
96 / 24 | AUTO SR | kHz | ||||||
|
|
|
|
|
|
|
| |
DVD MULTI 
DVR/DVD (DGT) 
VCR (DIGITAL) 
VIDEO (DGTL)
TV (DIGITAL) 
FM 
AM 
(Back to the beginning)
DVD MULTI: | Select for the DVD player using the |
| analogue discrete output mode (5.1- |
| channel reproduction). |
DVR/DVD (DGT)*: | Select for the DVD recorder or DVD player. |
VCR (DIGITAL)*: | Select for the VCR. |
VIDEO (DGTL)*: | Select for the component connected to the |
| VIDEO IN jacks on the rear of the receiver. |
TV (DIGITAL)*: | Select for the TV. |
FM: | Select for an FM broadcast. |
AM: | Select for an AM (MW) broadcast. |
From the remote control:
Press one of the source selecting buttons.
•For the tuner, press FM/AM. Each time you press FM/AM, the band alternates between “FM” and “AM.”
* Selecting the analogue or digital input mode
For a component you have connected using both the analogue connection and the digital connection methods (see pages 7 to 11), you need to select the correct input mode.
•You can select the digital input only for sources which you have selected digital input terminals for. (See “Setting the digital input (DIGITAL IN)
From the remote control ONLY:
Press ANALOG/DIGITAL INPUT to select the analogue or digital input mode.
•Each time you press the button, the input mode alternates between the analogue input (“ANALOGUE”) and the digital input (“DGTL AUTO”).
This setting is memorized for each source.
DGTL AUTO: Select for the digital input mode. The receiver automatically detects the incoming signal format, then the digital signal format indicator (LPCM, DOLBY D, DTS, or DTS 96/24) for the detected signal lights up.
ANALOGUE: Select for the analogue input mode.
To turn off the power (into standby)
Press 
STANDBY/ON (or 
AUDIO on the remote control) again.
The standby lamp lights in red.
NOTE
A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.
Initial setting: DGTL AUTO
NOTE
When you select “DVD MULTI,” “FM,” or “AM” as the source, the analogue and digital input mode is not available.
12
