12 EN GETTING STARTED

Power

 

NOTES:

 

 

 

 

It is recommended that only genuine JVC batteries are

This camcorder’s 2-way power supply system lets you

used in this camcorder. Using generic non-JVC batteries

choose the most appropriate source of power. Do not use

can cause damage to the internal charging circuitry.

If the protective cap is attached to the battery pack, remove

provided power supply units with other equipment.

it first.

 

 

 

 

 

 

Charging The Battery Pack

During charging, the camcorder cannot be operated.

Charging is not possible if the wrong type of battery is used.

 

 

 

 

When charging the battery pack for the first time or after a

Power switch

POWER/CHARGE lamp

long storage period, the POWER/CHARGE lamp may not

 

Battery pack

light. In this case, remove the battery pack from the

 

camcorder, then try charging again.

 

 

mount

If the battery operation time remains extremely short even

 

 

after having been fully charged, the battery is worn out and

 

Battery pack

needs to be replaced. Please purchase a new one.

 

 

Since the AC Adapter processes electricity internally, it

 

 

becomes warm during use. Be sure to use it only in well-

 

 

ventilated areas.

 

 

 

Arrow

Using the optional AA-V40 AC Power Adapter/Charger, you

 

can charge the BN-V408U/V416U/V428U/V438U battery

 

 

Open the cover.

 

pack without the camcorder. However, it cannot be used as

 

 

an AC Adapter.

 

 

To DC connector

 

After 5 minutes has elapsed in Record-Standby mode with the

 

cassette inserted, the camcorder will automatically turn off its

 

 

 

 

power supplied from the AC adapter. In this case, the battery

AC Adapter

 

charge starts if the battery is attached to the camcorder.

BATT. RELEASE

Using The Battery Pack

 

 

 

 

 

 

 

 

Perform steps 2 3 in “Charging The Battery Pack”.

Power cord

Maximum continuous recording time

 

 

To AC outlet

Battery pack

LCD monitor on

Viewfinder on

 

 

 

1 Set the Power Switch to “OFF”.

BN-V408U*

1 hr.

1 hr. 10 min.

BN-V416U

1 hr. 55 min.

2 hr. 15 min.

2 With the arrow on the battery pack pointing upward,

BN-V428U

3 hr. 20 min.

3 hr. 55 min.

push the battery pack slightly against the battery pack

BN-V438U

4 hr. 35 min.

5 hr. 20 min.

mount a.

 

* Provided

 

 

3 Slide up the battery pack until it locks in place b.

 

 

NOTES:

 

 

4 Connect the AC Adapter to the camcorder, then

 

 

Recording time is reduced significantly under the following

connect the Power Cord to the AC Adapter.

conditions:

 

 

5 Plug the Power Cord into an AC outlet. The POWER/

Zoom or Record-Standby mode is engaged repeatedly.

CHARGE lamp on the camcorder blinks to indicate

The LCD monitor is used repeatedly.

 

charging has started.

 

The playback mode is engaged repeatedly.

 

Before extended use, it is recommended that you prepare

6 When the POWER/CHARGE lamp goes out, charging

enough battery packs to cover 3 times the planned

is finished. Unplug the Power Cord from the AC outlet.

shooting time.

 

 

Disconnect the AC Adapter from the camcorder.

ATTENTION:

 

 

 

 

 

 

To detach the battery pack

Slide the battery pack down slightly while sliding BATT. RELEASE to detach it.

Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.

Battery pack

Charging time

 

 

BN-V408U*

Approx. 1 hr. 30 min.

 

 

BN-V416U

Approx. 3 hr.

 

 

BN-V428U

Approx. 5 hr.

 

 

BN-V438U

Approx. 6 hr. 30 min.

 

 

* Provided

Page 12
Image 12
JVC LYT1325-001A manual Power, Charging The Battery Pack, Using The Battery Pack, Maximum continuous recording time