MENUS FOR DETAILED ADJUSTMENT EN 31
SQUEEZE*
: For playback on TVs with an aspect ratio of 16:9. Naturally expands the image to fit the screen
without distortion. The 
indicator appears. When using this mode, refer to your
D.WIDE* 
: The 
indicator appears. The zoom range is extended beyond the maximum optical zoom wide angle range. This mode’s wide angle setting is equivalent to using a 0.7X wide conversion lens. Zooming is possible from 0.7X to 10X. This mode is suitable for shooting in a small room.
*Available only when the VIDEO/MEMORY Switch is set to “VIDEO”.
WIND CUT
[OFF]: Disengages the function.
ON 
: Helps cut down on noise created by wind. The “
” indicator appears. The quality of the sound will change. This is normal.
FLASH ADJ.
pg. 34, “Flash Brightness Adjustment”
NOTES:
●If a cassette is in the camcorder, the demonstration cannot be turned on.
●“DEMO MODE” remains “ON” even if the camcorder power is turned off.
●If “DEMO MODE” remains “ON”, some functions will not be available. After viewing demo, set to “OFF”.
160 x 120 / 240 x 176 / [352 x 288] |
pg. 26, “E-Mail Clip Recording”
PRIORITY
[LCD]: The image is displayed on the LCD monitor when the viewfinder is pulled out while the LCD monitor is opened.
FINDER: The image is displayed in the viewfinder when the viewfinder is pulled out while the LCD monitor is opened.
CAM RESET
EXECUTE: Resets all settings to the
[RETURN]: Does not reset all settings to the factory- preset.
SYSTEM
The “s SYSTEM” functions which are set when the Power Switch is set to “M” are also applied when the Power Switch is set to “PLAY”.
[ ] =
BEEP
OFF: Even though not heard while shooting, shutter sound is recorded on the tape.
BEEP: The beep sounds when the power is turned on or off, and at the beginning and end of recording. It also activates the shutter sound effect. ( pg. 23, 35) [MELODY]: Instead of a beep, a melody sounds when any operation is performed. It also activates the shutter sound effect. ( pg. 23, 35)
TALLY
OFF: The tally lamp remains off at all times.
[ON]: The tally lamp comes on to signal the start of recording.
REMOTE
OFF: Disables the remote control operations.
[ON]: Enables the remote control operations.
DEMO MODE
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as Program AE with special effects, etc., and can be used to confirm how these functions operate. Demonstration starts in the following cases:
●When the Menu Screen is closed after “DEMO MODE” is turned “ON”.
●With “DEMO MODE” set to “ON”, if there is no operation for about 3 minutes after the Power Switch is set to “A” or “M”.
●Performing any operation during the demonstration stops the demonstration temporarily. If no operation is performed for more than 3 minutes after that, the demonstration will resume.
CAMERA DISPLAY
●The “n” (CAMERA DISPLAY) settings are effective even when the Power Switch is set to “A”. However, the menu settings can be changed only when the Power Switch is set to “M”.
●The “n” (CAMERA DISPLAY) settings except “BRIGHT” and “AUX MIC” are effective only for shooting.
[ ] =
BRIGHT
pg. 15, “Brightness Adjustment Of The Display”
ON SCREEN
LCD: Keeps the camcorder’s display (except the date, time and time code) from appearing on the connected TV screen.
[LCD/TV]: Makes the camcorder’s display appear on screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5 seconds when the Power Switch is set from “OFF” to “A” or “M”. ON: The date/time is always displayed.
●The date indication can also be turned on/off by pressing the DISPLAY Button on the remote control (provided). ( pg. 21, 40, 45)
