•When unplugging the microphones, pull on the plug, not the cord itself.
NOTES
•Do not press any buttons on the remote control or the front panel of the receiver during Precise Surround Setup; otherwise, the receiver stops setting and returns to the normal operation mode.
–After “COMPLETE” is displayed, the Precise Surround Setup results are applied to the speaker settings.
•The speaker size measured by Precise Surround Setup may be different from that of the manual setting recommendation (see page 30). Precise Surround Setup measures the speaker size not only by the cone speaker size but also by the other speaker features.
•There may be a case that the receiver fails to detect subwoofer and does not activate it (no optimized test tone comes out of the subwoofer).
In such a case, set the volume level of the subwoofer higher and perform Precise Surround Setup again.
•When you change your listening environment, such as speakers, speaker position, your listening position or so, perform Precise Surround Setup again to optimize the speaker settings.
•Depending on the listening environment, Precise Surround Setup may not measure the speaker settings accurately. In such a case, adjust the settings manually. See pages 29 to 31, and 33.
•The supplied
•When the AV COMPU LINK remote control system works during Precise Surround Setup, this receiver stops setting and returns to the normal operation mode.
7 Turning the frequency optimizing function off
You can check the current settings of the frequency responses with test tones from speakers and the indications on the display when the frequency optimizing function is activated.
From the remote control ONLY:1Press TEST to check the frequency response of each speaker on the display.
TEST
•A test tone also comes from each speaker in the following order:
FL (Left front speaker) = C (Center speaker) = FR (Right front speaker) = SR (Right surround speaker) = SBR (Right surround back speaker)* = SBL (Left surround back speaker)* = SL (Left surround speaker) = SW (Subwoofer) * When using a single speaker for the surround back
speaker, the test tone comes out of “SB (Surround back speaker)” instead of “SBR” and “SBL.”
After performing Precise Surround Setup, the receiver | • The frequency response of each speaker appears on the | ||||||||||||
optimizes the frequency response for each speaker. | display as follows: |
|
|
|
|
|
| ||||||
You can turn the frequency optimizing function off. | EX. 1: When a test tone comes from the left front speaker | ||||||||||||
|
| ||||||||||||
| Press PSS to turn the frequency optimizing | Current speaker |
| Frequency response | ||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
| function off. |
|
|
|
|
|
|
|
|
| +9 dB | |||
|
|
|
|
|
|
|
|
| |||||
• Each time you press the button, the frequency optimizing |
|
|
|
|
|
|
|
|
|
| Optimizing level | ||
|
|
|
|
|
|
|
|
|
| ||||
function alternates between on and off. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||||
When the function is activated, the PSS indicator is lit. |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |||||
|
| Low | Frequency | High | |||||||||
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
NOTE |
| EX. 2: When a test tone comes from the subwoofer | |||||||||||
This function is not available: | |||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
– Until Precise Surround Setup has been completed at least once; |
|
|
|
|
|
|
|
|
|
| Crossover | ||
otherwise, “NO PSS” appears on the display. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| frequency | |||
– When selecting “A MULTI” for the audio input setting (see page 11). |
|
|
|
|
|
|
|
|
|
| |||
– When |
|
|
|
|
|
|
|
|
|
|
| ||
selecting “HDMI” for the audio input setting (see page 11). |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 80 Hz |
| 200 Hz | ||||||||
|
|
|
|
|
| ||||||||
NOTE
While the PSS indicator is off, pressing TEST generates test tones without showing frequency responses. See page 36.
18