Setting the digital input (DIGITAL IN) terminals—DIGITAL IN 1/2/3

When you use the digital input terminals, register what components are connected to which terminals—DIGITAL IN 1/2/3 (see page 14) so that the correct source name will appear when you select the digital source.

Select one of the following components for each terminal:

DVR/DVD

For the DVD player (or DVD recorder)

DBS

For the DBS tuner

 

 

VCR

For the VCR

 

 

TV

For the TV

 

 

Initial setting:

DVR/DVD (for “DIGITAL IN 1”)

 

DBS (for “DIGITAL IN 2”)

 

VCR (for “DIGITAL IN 3”)

NOTES

•You cannot assign the same component for different terminals. The priority order for assignment is as follows:

“DIGITAL IN 1” > “DIGITAL IN 2” > “DIGITAL IN 3” Ex.: When “DIGITAL IN 1” is set to “DVR/DVD.”

DIGITAL IN 1

DVR/DVD

DBS

VCR

TV

 

 

 

 

 

‘

For “DIGITAL IN 2,” “DBS,” “VCR,” and “TV” are selectable.

• In this case, “VCR” is selected.

DIGITAL IN 2

DVR/DVD

DBS

VCR

TV

 

 

 

 

 

‘

For “DIGITAL IN 3,” “DBS” and “TV” are selectable.

DIGITAL IN 3

DVR/DVD

DBS

VCR

TV

 

 

 

 

 

 

 

 

 

 

: Selectable

 

 

: Not selectable

 

 

 

 

 

 

 

 

 

 

 

 

•Setting “DIGITAL IN 1” affects “DIGITAL IN 2” and “DIGITAL IN 3” settings. When you have changed “DIGITAL IN 1,” confirm the components assigned to “DIGITAL IN 2” and “DIGITAL IN 3.”

Setting the Audio delay level—

AUDIO DELAY

Synchronization between audio and video reproduction can be possibly disturbed because video signal decoding is time- consuming compared to the audio signal decoding.

On this setting, you can correct synchronization between video and audio signals by delaying the audio signal timing.

Adjustable range: OFF and 10 ms to 150 ms (in 10 ms intervals)

Initial setting:

OFF

NOTE

The audio delay level setting does not take effect when selecting “A MULTI” for the audio input setting (see page 11).

Selecting the source for HDMI terminal and COMPONENT VIDEO jacks—HDMI SELECT/CMPNT SELECT

When you connect a VCR or DBS to the HDMI VCR(DBS) IN terminal or COMPONENT VIDEO jacks on the rear of the receiver, you need to select either “VCR” or “DBS” for each terminal according to the component you connect.

If you have not selected an appropriate source, you cannot view the playback picture on the TV.

For the HDMI terminal:

HDMI VCR

Select this when connecting a VCR to the

 

HDMI terminal.

 

 

HDMI DBS

Select this when connecting a DBS tuner to

 

the HDMI terminal.

 

 

Initial setting:

VCR

For the COMPONENT VIDEO jacks:

CMPNT VCR Select this when connecting a VCR to the COMPONENT VIDEO jacks.

CMPNT DBS Select this when connecting a DBS tuner to the COMPONENT VIDEO jacks.

Initial setting: VCR

Selecting the output video signals—

VIDEO OUTPUT

When you connect your TV and this receiver with the HDMI cable, set this setting to “HDMI.”

With this setting, this receiver converts incoming composite video, S-video, and component video signals from video components and transmits the converted signals through the HDMI cable.

VIDEO HDMI Select this when connecting a TV to the HDMI terminal.

VIDEO OTHER Select this when connecting a TV to any video jack other than the HDMI terminal.

Initial setting: HDMI

NOTE

When selecting “HDMI,” the AV COMPU LINK remote control system is restricted (see page 45).

34