OPERATIONS ON DVD DECK EN 37

Recording Features

 

 

8 To record the entire program within the actual remaining

 

 

disc space

 

 

 

Select “FR (JUST)” in a recording mode selection procedure.

 

 

 

( pg. 38, 39)

 

 

 

● Note that this function is available only for timer programming

 

 

 

recording.

● Turn on the unit.

 

 

8 To record the entire program by specifying the desired

 

 

recording time

● Turn on the TV and select the video channel (or AV mode).

Select “FR60–FR360”, “FR420” or “FR480” in a recording mode

● Slide the TV/CABLE/DBS/DVD switch to DVD.

selection procedure. ( pg. 36, 38, 39)

● Press VCR/DVD repeatedly so that the DVD lamp lights up on the

unit.

 

 

8 To record a 25-min. long daily program five times just on a

 

 

 

 

 

 

same disc for example

 

 

 

Perform “VCR Plus+ Timer Programming” ( pg. 38) procedure.

 

 

 

Be sure to set the recording mode to “FR125” and set Weekly/Daily

 

 

 

Rec Function to “MON–FRI” in step 6 to fit the total recording time

1

2

3

to the whole disc space.

 

4

5

6

 

7 8 9

0

DISPLAY

REMAIN

 

TV/VCR

CH +/–

 

Watch Another Program While Recording On The Unit

While recording is going on, you can watch another program on the TV by using the TV’s tuner.

NOTE:

It is required that the remote control is set to be able to operate the TV in advance. ( pg. 66)

1 During recording, press TV/VCR to select TV mode if your unit is connected to the TV via the RF connection.

●VCR mode is disengaged, then the VIDEO indicator lights off and “TV” appears on the front display panel.

VIDEO indicator lights off.

●The program received on the TV’s tuner is displayed on the TV screen.

2 Slide the TV/CABLE/DBS/DVD switch to TV.

3 Press CH +/– repeatedly to select the desired channel.

Elapsed Recording Time And Disc Remaining Time Indication

During recording, press DISPLAY repeatedly until the desired indication appears on the front display panel.

●Each time you press DISPLAY, the time indication changes as follows:

Elapsed recording time ] Disc remaining time ] Clock ] (Back to the beginning)

●You can also check the disc remaining time by pressing REMAIN while the unit is stopped or recording is in progress. The list of disc remaining times for all recording modes appears on the TV screen.

Free Rate Function

To record the entire program, the unit automatically set the appropriate recording mode depending on the combination of the total time of the program to be recorded and either the remaining disc space or the specified recording time (from 60 minutes to 480 minutes).

A: 1st

BlankB: 2nd

C: 3rd

D: 4th

E: 5th

When the same program is recorded in SP mode instead of in “FR125”, the 5th program cannot be recorded.

 

A: 1st

Blank

B: 2nd

C: 3rd

 

 

D: 4th

 

E: Blank (20 min.)

NOTES:

●You can program this unit to timer record, regardless of the disc remaining time. When the disc remaining time is not enough, recording may stop in the middle of a program. To avoid this, make sure of the disc remaining time before setting timer programming. (Example) If you programmed to timer record for 60 minutes in SP mode on a 120-minute disc, the disc remaining time would be 30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP mode, 180 minutes in EP mode, and 240 minutes in FR480 mode. Timer recording will not complete beyond these remaining times.

●The maximum recording time of FR (JUST) mode is the same as the recording time of FR480 mode. When timer programming a long program in FR (JUST) mode on a disc whose remaining time is short, it is recommended checking the disc remaining time in FR480 mode to see if the remaining time is enough for the program.

●Even if more than one program are timer programmed in FR (JUST) mode, only the first one is recorded.

●In order to ensure that the recording fits on the disc, this feature may leave a slight non-recorded section at the end of the disc.

●There may be some noise and sound disturbance at the point on the disc where the unit switches the mode.

Second Audio Recording

This unit’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set “2ND AUDIO RECORD” to “ON”. ( pg. 70)

NOTE:

When the channel is changed on the unit;

●The “MONO” indicator appears on the screen for about 5 seconds if the program is a monaural broadcast.

●The “STEREO” indicator appears on the screen for about 5 seconds if the program is a stereo broadcast.

●Both “STEREO” and “SAP” indicators appear when a stereo program is accompanied by SAP sound.

●Both “MONO” and “SAP” indicators appear when the main audio on the monaural broadcast is accompanied by SAP sound.