JVC SR-MV40U Disc, ENTER, ENTER, ENTER, ENTER, VCR/DVD, DVD TIMER, PROG/CHECK, time on the disc, 40 EN OPERATIONS ON DVD DECK, To Make The Disc For On-DiscTimer Programming

40 EN OPERATIONS ON DVD DECK

			On-Disc Timer Programming							7 Press w e to select “STOP”, then press rt to set the desired
										stop time.
										● Each press of rt increases/decreases the stop time in 1-minute
										intervals.
										● To increase/decrease the stop time in 30-minute intervals, press and
										hold rt.
										8 Press w e to select “CH”, then press rt to select the desired
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific program. The disc is then										channel.
										9 Set “DAILY/WEEKLY” option.
programmed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single										● Refer to step 6 in “VCR Plus+ Timer Programming” ( pg. 38).
DVD-RAM/RW (VR mode) disc can be used without worrying										● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
about how much recording capacity remains. ( pg. 41)										Programming. ( pg. 38, “Daily/Weekly Recording”)
You can program each disc to timer record as many as 8 programs.										10 Set the other recording options as required.
										● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
	● Make sure that the unit’s built-in clock is set properly.									However, you cannot select FR (JUST), FR60–FR360 and FR420.
	● Turn on the unit.									● Refer to step 6 in “VCR Plus+ Timer Programming” ( pg. 38).
	● Turn on the TV and select the video channel (or AV mode).									● It is not possible to use the Free Rate function. ( pg. 37)
	● Slide the TV/CABLE/DBS/DVD switch to DVD.									11 Press ENTER to access the Program Confirmation screen.
										12 Press ENTER to complete timer programming.
	ATTENTION:
										● To program another timer, repeat steps 3 – 12.
	● On-Disc Timer Programming is possible only with the disc for On-									To Timer record The Program With The Programmed
			Disc Timer Programming.
	● If data is recorded on a disc for On-Disc Timer Programming using									Disc
			a unit from another manufacturer, On-Disc Timer Programming
			may no longer function properly.
										1 Load a programmed disc.
										2 Press DVD TIMER (#). The unit turns off and “	” appears
				DVD TIMER (#)						on the front display panel. The DVD timer indicator also lights up
										on the front display panel and the VCR deck is automatically
					VCR/DVD
						1	2	3	1	selected. When the VCR deck is in timer standby mode, the unit is
						4	5	6		automatically turned off.
						7	8	9
										● To disengage the timer mode, press 1 again.
				PROG/CHECK			0
										NOTES:
					ENTER				rtw e	● When On-Disc Timer Programming overlaps with other timer
										programming, for example VCR Plus+ Timer Programming, no
										caution message will be displayed.
										However, when On-Disc timer programs overlap, a caution message
										will be displayed.
										● On-Disc Timer Programming is not possible on a DVD-RW disc
										formatted in video mode. ( pg. 75)
										● The information of a program recorded with On-Disc Timer
										Programming is not stored in the library. ( pg. 56)
										● The play list is not created for the programs recorded with On-Disc
										Timer Programming. ( pg. 54)
										● VCR Plus+ Timer Programming is not possible on the discs used
To Make The Disc For On-Disc Timer Programming										exclusively for On-Disc Timer Programming.
										● Manual Timer Programming is not possible on the On-Disc Timer
										Programmed disc. ( pg. 39)
1 Load a recordable disc.										● Basic Recording is not possible on the On-Disc Timer Programmed
										disc. ( pg. 36)
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on
										● The On-Disc Timer Programming function does not work on the unit
the unit.										form other manufactures even if the On-Disc Timer Programmed disc
3 Press PROG/CHECK to access the Program Check screen.										is loaded.
										● The beginning of a program may not be recorded. Also, if the 1st
4 When On-Disc Timer Programming is made for the first
										program’s recording stop time and the 2nd program’s recording start
time on the disc										time is the same, the ending of the 1st program may not be recorded.
Press rt to select “DISC TIMER PRGM”, then press ENTER.										● If there is a power cut while recording, the recordings before the
● When some programs are recorded on the disc, a caution message										power cut are not guaranteed.
		appears. In such a case, backup the programs as required, then

format the disc before making On-Disc Timer Programming. ( pg. 75)

When On-Disc Timer Programming has already been made on the disc

Press rt to select “NEW TIMER PROGRAM”, then press

ENTER.

5 Press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt increases/decreases the start time in 1-minute intervals.

●To increase/decrease the start time in 30-minute intervals, press and hold rt.