INTRODUCTION
Controls, Connectors and Indicators (Continued)
13 | [ | , | , | , | ] |
| right Button |
| |||
| These buttons select items on the menu | ||||
| screen and change a set value. | ||||
| ( Page 23) |
| |||
14 | |
| Switch of External Synchronization |
| Signal |
| This is a terminating ON/OFF switch for |
17
SIMPLEX: This switch sets to SIMPLEX when the transmission between the camera and a remote control unit is in a simplex system
| ( | ) |
|
| ⁄ | |
| + | - |
|
|
|
|
| 1 | 2 |
|
|
|
|
DC12V | AC24V | CLASS2 ONLY(U TYPE) ISOLATEDPOWER ONLY (E TYPE) | TX- RX+ RX- | AUX GND | ||
|
| TX+ | ||||
|
| A | B | C | D |
|
| the external synchronization input signal. |
| When this is switched ON, termination is |
| executed via a 75 Ω resistor. |
| ON: terminates at 75Ω. |
| OFF: does not terminate at 75Ω. |
| (ON: At time of factory shipment) |
15 | [INT/GL, LL] Selector Switch for |
| Synchronizing System |
between RX + and RX – on the back 20 should be terminated at the value of 110Ω resistance. ON: Terminated. OFF: Not terminated. If the system including the camera is the M.DROP
fi ›
SYNC IN | VIDEO OUT |
POWER |
|
‹
Y/C OUT 
¤ SEE INST- RUCTION MANUAL
| This switch sets the synchronizing system |
| for the camera. |
| INT/GL: |
| This is set for internal synchronization |
| (INT) or external synchronization (GL). |
| LL (Line Lock): |
| The camera’s vertical synchronization is |
| locked to the AC 24V power line frequency. |
| When switching between multiple |
| cameras using a switcher, selecting this |
| mode and adjusting the vertical phase |
| can reduce the monitor sync disturbances |
| occur that when the camera image is |
| switched. (This cannot be used in regions |
| where the power frequency is 60 Hz) |
| (INT/GL: At time of factory shipment) |
16 | [DUPLEX, SIMPLEX] Selector Switch |
| for Transmission System |
| If the setting is changed, be absolutely |
| sure to switch on the power again. |
| DUPLEX: |
| This switch sets to DUPLEX when the |
| transmission between the camera and a |
| remote control unit is in a duplex system |
|
18
control signal cable is set to “ON” and the other cameras are set to “OFF”. In case of the M.DROP system, it becomes necessary to set the Machine ID. ( Page 35) If the system including the camera is the P TO P (Point to Point,
NOT USED This cannot be used. Do not switch.
19 | [DC 12V, AC 24V] Power input terminals |
| To input DC 12V or AC 24V power. |
20 | [TX+A, |
| signal connection terminals |
| Terminals for inputting signals with |
| electrical characteristics conforming to |
| the EIA/TIA |
| 17 RX.TERM switch |
21 | [AUX, GND] Auxiliary Input/Output |
| Terminals |
| If there is any change in the area set on |
| the MOTION DETECT screen, these |
| terminals output the corresponding |
| signals. ( Page 34) |
| These terminals also output the B&W/ |
| COLOUR signal. ( Page 30) |
| |
| voltage 30V, current 30mA.] |
| When carrying out B&W/COLOUR |
| switching using the control signal, the |
| signals are input through these terminals. |
| ( Page 30) |
| [B&W: make; COLOUR: break] |
22 | [Y/C OUT] Y/C output connector |
| This |
| and chrominance signal. |
| • Pin configuration of Y/C OUT connector |
4 | 3 |
2 | 1 |
Pin No. | Signal |
1GND
2GND
3Luminance (Y)
4Chrominance (C)
23 | [VIDEO OUT] Video signal output |
| connector |
| This BNC connector outputs a composite |
| video signal. Connect this to the video input |
| connector of a video monitor, switcher, etc. |
24 | [POWER] Power indicator lamp |
| This lamp lights when power is supplied |
| to the camera. |
25 | [SYNC IN] Sync signal input connector |
| This BNC connector accepts the input of |
| an external sync signal such as a composite |
| video (VBS) or black burst (BB) signal. |
| When a sync signal is input into this |
| connector, the camera operation is |
| automatically synchronized with the |
| external sync signal. |
| To terminate this connector at 75Ω, turn |
| ON the EXT.TERM switch 14 . |
