CONNECTION/INSTALLATION
RM-P2580 System
System with up to 8 cameras
Connecting the control signal cable
(Use a twisted-pair cable for connection. Page 17.)
Camera 1
MACHINE ID:1 (Menu screen) RX TERM: OFF (switch)
Camera
Camera
Control signal cable | ||
Video signal cable | ||
Power | AC24V | |
or | ||
cable | ||
DC12V | ||
| ||
Camera 1 |
|
control signal | |
connection terminals | |
TX+ A | |
TX | B |
RX+ C | |
A RX | + |
B RX | + |
C TX | |
Connect: Camera TX+ to
Camera 2 | AC24V | |
MACHINE ID:2 | ||
or | ||
(Menu screen) | ||
DC12V | ||
RX TERM: OFF | ||
| ||
(switch) |
| |
| Camera | |
|
RX | D |
Camera 2 |
|
control signal | |
connection terminals | |
TX+ A | |
D TX |
Camera RX– to
Camera 8
MACHINE ID:8 (Menu screen) RX TERM: ON (switch)
AC24V | • | • | • | • | • | CAM SW | Time lapse VCR | |
or | ||||||||
|
|
|
|
| OUT | |||
DC12V |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| VIDEO IN |
MONITOR
TX | B |
RX+ C | |
RX | D |
Setting the switches | ( Page 10) |
Remote Control Unit RM-P2580
TO CAMERA
TO CAMERA
- -
POWER
OFF
AC
INPUT
|
|
| CAMERA |
|
|
|
| ||
|
|
|
| SW | COM |
|
| ||
|
|
| DATA I / O |
|
|
|
| ||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| MONITOR |
|
|
|
| VIDEO INPUT |
|
|
|
|
|
|
|
|
|
|
|
| MONITOR MONITOR | OUTPUT 2 | |
|
|
|
|
|
|
| 1 | 2 | |
|
|
|
|
|
|
| OUTPUT OUTPUT |
| |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
|
|
| VIDEO OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
| MONITOR | |
|
|
|
|
|
|
|
| OUTPUT 1 | |
MONITOR
EXT | ON |
INT/GLLL
DUPLEXSIMPLEX
RX | ON |
Select the synchronization method of the camera image. Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE. ( Page 26.)
Set this switch to the DUPLEX
* If the setting is changed, be absolutely sure to |
switch on the power again. |
This is the connected example of the |
|
When controlling with any system except the | |
switches and menu screens according to the systems used. | ( Page 14) |
MEMO |
|
VIDEO
DC
IRIS
NOT USED 
Set this switch to ON (signal termination ON) only on the camera placed at the end of the control signal cable. Set to OFF on all other cameras.
•When operating a system using the
•Confirm switch settings on the screen as follows.MONITOR screen
q Confirm that the image from the camera to be checked | (example showing camera ID as “05”) |
| |
is displayed on the monitor. |
|
w Turn OFF and then ON the AC 24 V power to the cam- |
|
|
|
| |
era to be checked. |
|
|
|
| |
e The camera begins the initial operation and characters |
|
|
|
| |
similar to those shown in the illustration on the right |
|
|
|
| |
appear on the monitor screen. |
|
|
|
| |
r Confirm that “DUPLEX” and |
|
|
|
| |
that the ID number is the correct number (the number | P R O T O C O L : D U P L E X | I D - 0 5 | |||
|
|
|
| ||
should be the same as the number of the VIDEO IN- |
|
|
|
| |
PUT terminal to which the camera is connected on the |
|
|
|
| |
rear panel of the | “DUPLEX” | should | The number shown in the | ||
t If wrong, set the camera ID again. | |||||
be displayed. | □ □ part of | ||||
| should be correct. | ||||
|
| ||||
|
|
|
| ||
Setting on the MENU screen ( Page 33)
* If the setting is changed, escape from the menu screen once, and definitely switch on the power again. | |||
C OMMUN I C A T I O N |
| Set to M.DROP | |
| Set to M.DROP when the | ||
|
| ||
S T YL E | M . DROP | as a remote control unit. When controlling | |
MACH I NE I D | 1 | ||
from another machine, make sure that it | |||
|
| ||
|
| matches the communication system used. | |
MACHINE ID setting switches
Set this item to match the
INPUT terminal number for each camera.
When connecting
●Turn OFF the power supply to all equipment to be used before making connections.
●Carefully read the Instructions for each piece of equipment to be used before making connections.
●For the appropriate connection cables and the length of these, carefully read “Connections on the back” on page 16.
●The control signal cable cannot be used for loop connection.
