Main Wheel Axle Assembly. Serial No’s 357 to February | Kenmore

MAINTENANCE

Main Wheel Axle Assembly. Serial No’s 357 to February 2007.

Taper Roller Axles should be checked every 12 months. To remove a Wheel/Axle Assembly :

Fig.28

•Lower Reels to the ground. Remove Reels 4 and 5.

•Jack-up and support the Mower frame. Remove the Bearing Blocks and the Wheel/Axle Assembly.

•Remove the Wheel from the Axle Hub.

•Remove Retainer Bolt, and End Cap from the Axle.

•Release the two Setscrews and remove the Axle Nut and Spacer.

•Pull the Hub off the Axle.

•Remove the Seals and Bearings from the Hub.

•Clean the Bearings. If there are signs of wear or damage, replace Cups and Cones as assemblies.

•Pack Bearings and Hub with grease. Fit new Seals.

•Fit the Hub onto the Axle. Install the Spacer, Axle Nut and End Cap with Retainer Bolt.

•Tighten the Axle Nut, while turning the Hub, until it is difficult to turn, then back-off the Axle Nut ¼ turn and tighten the Setscrews.

•Fit the Wheel to the Hub. Install the Wheel/Axle Assembly into Mower Frame. Tighten Bearing Blocks.

•Torque the Wheel Nuts to 90 ft/lb.

Fig.28

34

Image 37

Kenmore 11, 9 manual Main Wheel Axle Assembly. Serial No’s 357 to February

Contents

Kesmac Foreword Kesmac Transportable Reel Mowers Maintenance Contents Safety Precautions Vertical Mower General SafetySpecifications HOOK-UP to Tractor Lift Cain Adjustment Eleven Gang Mowing Procedure If you do not understand……….ASK Maintenance Safety Safety Precautions General SafetyBe a Qualified Operator by Before Operating the Mower Safety Alert Symbol During Maintenance DECALS. See Pages 5 & 6 also Page Page Operating Conditions Tires Mainwheel BearingsMain and Outrigger Turf tires are not designed for use on highways Daily Inspection Primary Belts Daily Inspection Drive Belts and SheavesReel Drive Belts Tongue Tube Daily Inspection PTO Shaft Daily Inspection Hydraulic System This check should be done at regular service intervalsGuards and Decals To do so may result in serious personal injury Mower Transport Wheel Bearing Service Life Transport Lowering the Reels Transport Safety ChainsDo not set the tractor engine RPM too high Lifting the Reels REEL/WING Lower Sequence Hydraulic Lift Operation REEL/WING Lift Sequence Hydraulic Lift Operation REEL/WING Lift Sequence Sequence Valve Setting , 9 & 11 Gang only Relief Valve Setting Reels 4 Lift Chain Adjustments Reels 4 and 5 Lift Chains Adjustment Cutting Height Adjusment Cutting Height Adjustment FAIRWAY. Floating Head Pre-single point adjustment units Reel to BED Knife Adjustment Reel to BED-KNIFE Single Point Adjustment Drive Belt Adjustment Vertical MOWER. Depth of CUT Adjustment Vertical Mower Operation Hours or Weekly Routine MaintenanceHours Annual Maintenance Inspection Lubrication = Grease. B = Oil Gearbox Lubrication Gearbox Lubrication Cones as assemblies Main Wheel Axle Assembly . From Feb.07 Main Wheel Axle Assembly. Serial No’s 357 to February Single Outrigger Wheel Dual Outrigger Wheels Outrigger Single Wheel. From Serial No Wing Kick Springs Main Drive Belts Reel Drive Belts Maintenance Maintenance PTO Shaft SET- UP Main Jackshaft Bearing replacementShafts must be set-up as illustrated Gang Gang 7-Gang 5-Gang Gang 9-Gang Specifications Tractor POWER. Nominal Specifications Primary DriveSTEP-UP Drive Ratio Number of Reels Hydraulic Operation Backlapping Attachment Backlapping Operation Reel and Bedknife Sharpening Optional Castor Wheel Gang only Wing Frame Lift Chains Attachment Points Grade 5 and 8 Fasteners. Coarse Thread Torque GuideSize Plated Plain