Kenwood BT948HD, KDC-X995 5Exit BT Settings mode Press the [] button, Turn the [VOL] knob to select a setting value, and then press the [VOL] knob

Display			Overview
“SMS Inbox”			Display the received short message.
			Refer to <SMS (Short Message Service)>
			(page 54).
“BT Settings”
	“Pairing”
		“Device Regist.”	Register a Bluetooth device (pairing).
			Refer to <Registering Bluetooth device>
			(page 50).
		“Phone	Select a cell-phone connection.
		Selection”	Refer to <Selecting the Bluetooth device You
			Wish to Connect> (page 51).
		“SPCL DVC	Register a Bluetooth device (pairing).
		Select”	Refer to <Registering Bluetooth device>
			(page 50).
		“Device Delete”	Cancel registration of the Bluetooth device.
			Refer to <Deleting a Registered Bluetooth
			device> (page 52).
	“SMS Download”		Download a short message.
			Refer to <Downloading the SMS> (page 54).
	“Voice Tag”		Registers voice for voice recognition and voice
			to select the Phone number category in Phone
			book.
			- Adding a Voice Dialing Command (page 52)
			- Setting a Voice Command for Category (page
			53)
	“Detailed Setup”		Move to detailed item.
		“PIN Code Edit”	Specify the PIN code required when registering
			this unit using the Bluetooth device.
			Refer to <Registering PIN Code> (page 51).
		“Auto Answer”	Answer a call automatically after lapse of the
			preset time interval for automatic answer.
			“OFF”/ “0s” – “8s” – “99s”
		“Auto	Automatically reconnects the selected
		Reconnect”*2	Bluetooth device when radio wave becomes
			strong enough, even after it is disconnected.
			“ON”/ “OFF”
			✍✍ When this function is enabled, the
			Bluetooth device is reconnected
			even if “Phone Selection” is selected
			to select a cell-phone connection.
			To cancel the Bluetooth connection,
			select OFF to disable this function.
		“Bluetooth HF”	You can specify output speakers for hands-free
			voice communication.
			“FRONT”: Outputs voice from the front
			speakers.
			“ALL”: Outputs voice from the front and rear
			speakers.
		“Call Beep”	You can output a beep from the speaker when
			a call comes in.
			“ON”: Beep is heard.
			“OFF”: Beep is canceled.

“BT F/W Update” Display the version of the firmware of this unit.

“Mic Gain”	Adjust the sensitivity of the microphone for a
	telephone call. Adjust the voice of caller. Setting
	to “+” increases the voice volume.
	“–3” – “0” – “+3”
“NR Level”	Reduce the noises generated by surrounding
	environment without changing the microphone
	volume. Adjust the voice of caller when it is
	not clear. Setting to “+” increases the noise
	reduction.
	“–3” – “0” – “+3”
“Echo Cancel LV“	Adjust the level of echo cancellation. Setting to
	“+” increases the echo cancel reduction.
	“–2” – “0” – “+2”
	(	: Factory setting)

4Make a setting

•When the “  PUSH  ” icon is displayed (at the right edge of the display)

Turn the [VOL] knob to select a setting value, and then press the [VOL] knob.

•When the “  PUSH  ” icon is not displayed Press the [4] or [¢] button to select a setting value.

5Exit BT Settings mode Press the [] button.

Remarks

•“Auto Answer”  (Setting the Time Interval for Automatic Answer)

This function automatically answers (responds to) a call after lapse of the preset time interval for automatic answer. “OFF” : Does not answer the phone call automatically.

“0” : Automatically answers the phone call at once.

“1s” – “99s” : Automatically answers the phone call after lapse of 1 – 99 seconds.

⁄

•If the time set in the cell-phone is shorter than that set in the unit, the former will be used.

•This function does not work for call waiting.

•“Bluetooth HF”  (Setting up the Voice Output Speakers) Select the speaker which is further from the microphone in order to prevent howling or echoes.

•“BT F/W Update”  (Displaying the Firmware Version)

Display the version of the firmware of this unit.

For how to update the firmware, access our web site. http://www.kenwood.com/cs/ce/bt/

English 49