Kenwood BT948HD, KDC-X995 Item, Range, Display, Operation, Select “YES”, X’Over Setting, Operation type, Select the source, 1Select the source, Audio Preset Memory

DSP Setup

X’Over Setting

Fine adjusting the following setting values corresponding to the X’Over values set in the section <Speaker Setting> (page 44).

Display		Item	Range
“X’Over”
	“Front”	“FC”	Front High Pass Filter
			Through, 30*, 40, 50*, 60, 70, 80,
			90*, 100, 120, 150, 180, 220, 250*
			(Hz)
		“SLOPE”*	Front High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“Rear”	“FC”	Rear High Pass Filter
			Through, 30*, 40, 50*, 60, 70, 80,
			90*, 100, 120, 150, 180, 220, 250*
			(Hz)
		“SLOPE”*	Rear High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“SubWoofer”	“FC”	Subwoofer Low Pass Filter
			30*, 40, 50*, 60, 70, 80, 90*, 100,
			120, 150, 180, 220, 250*, Through
			(Hz)
		“SLOPE”*	Subwoofer Slope
			-6, -12, -18, -24 dB/Oct
		“PHASE”	Subwoofer Phase
			Reverse (180°)/ Normal (0°)
			(	: Factory setting)

*Function of KDC-X995

1Select the source

Pressing the [SRC] button repeatedly switches source.

Select a source other than “STANDBY”.

2Enter Audio Control mode Press the [VOL] knob.

3Enter X’Over setting mode

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Detailed Setup” > “X’Over”.4Select the speaker you want to set

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Front”, “Rear”, or “SubWoofer”.5Select the item you want to set

Operation type	Operation
Selects the item.	Turn the [VOL] knob.
Adjust each item.	Press the [4] or [¢] button.
Set the value	Press the [VOL] button.

6Repeat steps 3 to 4 to complete the X’Over settings.

46KDC-X995/ KDC-BT948HD

7Exit Audio Control mode

Press the [MENU] button for at least 1 second.

Audio Preset Memory

Registering the value setup by Sound Control.

1Setup Sound Control

Refer to the following operations to setup the Sound Control.

-Car Type Selection (page 44)

-Speaker Setting (page 44)

-Car Type Fine Adjustments (page 45)

-X’Over Setting (page 46)

-Manual Equalizer Control (page 41)

-Listening Position Selection (page 42)

-Listening Position Fine Adjustments (page 42)

2Enter Audio preset memory mode

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Detailed Setup” > “Preset” > “Memory”.

3Select the number to put in the memory Turn the [VOL] knob and press it when the desired item is displayed.

Select a preset number.

4Turn the [VOL] knob and press it when the desired item is displayed.

Select “YES”.

“Memory Completed” is displayed.

5Exit Audio Control mode

Press the [MENU] button for at least 1 second.

⁄

•Register 2 patterns of Audio Preset Memory.

•Preset number “1”:

When you press the Reset, all the sources will be the setting value which is registered.

•Preset number “1” and “2”:

The memory cannot be erased by the Reset button.

•This function cannot be registered when the iPod Equalizer set in <Preset Equalizer curve Select> (page 41).