Reverse Function, Automatic Simplex Check ASC | Kenwood TM-D700E

REVERSE FUNCTION

The reverse function exchanges a separate receive and transmit frequency. So, while using a repeater, you can manually check the strength of a signal that you receive directly from the other station. If the station’s signal is strong, both stations should move to a simplex frequency and free up the repeater.

		MHz	145
	. 725		.
144	. 725		325
144			MHz
			144.725 MHz
				REV ON
TX: 144.725 MHz			TX: 144.725 MHz TX: 144.725 MHz	TX: 145.325 MHz
RX: 145.325 MHz			RX: 145.325 MHz RX: 145.325 MHz	RX: 144.725 MHz

Press [REV] to switch the Reverse function ON (or OFF).

•“R” appears when the function is ON.

Note:

◆If pressing [REV] places the transmit frequency outside the allowable range, then pressing Mic [PTT] causes an error beep to sound; transmission is inhibited.

◆If pressing [REV] places the receive frequency outside the allowable range, an error beep sounds and no reversal occurs.

◆Automatic Repeater Offset does not function while Reverse is ON.

◆You cannot switch Reverse ON or OFF while transmitting.

AUTOMATIC SIMPLEX CHECK (ASC)

While using a repeater, ASC periodically monitors the strength of a signal that you receive directly from the other station. If the station’s signal is strong enough to allow direct contact without a repeater, the ASC indicator on the display begins blinking.

Press [REV] (1 s) to switch the function ON.

• The ASC indicator appears when the function is ON.

6

•While direct contact is possible, the ASC indicator blinks.

•To quit the function, press [REV].

Note:

◆Pressing Mic [PTT] causes the ASC indicator to quit blinking.

◆ASC does not function if your transmit and receive frequencies are the same (simplex operation).

◆ASC does not function while scanning.

◆Activating ASC while using Reverse switches Reverse OFF.

◆If you recall a memory channel or the Call channel that contains Reverse ON status, ASC is switched OFF.

◆ASC causes receive audio to be momentarily intermitted every 3 seconds.

33

Image 39

Kenwood TM-D700E Reverse Function, Automatic Simplex Check ASC, Press REV to switch the Reverse function on or OFF

Contents

TM-D700A Features Thank YOUModels Covered by this Manual One or more of the following statements may be applicable When condensation occurs inside the transceiver Contents Locking Out a Memory Channel Selecting the Number of Channels Using Visual ScanSetting Scan Limits Using Program Scan Recalling the Call Channel Reprogramming the Call Channel Squelch Hang Time Changing MULTI-FUNCTION Conventions Followed in this Manual Supplied Accessories Mobile Installation Main Unit InstallationPreparation Slide the front panel down until its locking tab clicks Front Panel Installation Modular Plug Cable Connection Fixed Station Installation Mobile Operation DC Power Cable Connection PS-33 20.5 A, 25% duty cycle Fixed Station Operation Fuse Location Fuse Current Rating Transceiver 15 a Supplied Accessory 20 a DC Power CableAntenna Connection Replacing Fuses Accessory Connections External SpeakersMicrophone Ew wew w Your First QSO Front Panel Getting Acquainted 3SQL control Main UNIT- Front Main UNIT- RearGPS jack Microphone Indicators Basic Transceiver Modes Button Function Display Control Band Band a & BTX Band and Control Band TX Band MIC Keypad Direct Entry MC-53DM only Operating Basics Switching Power ON/OFFAdjusting Volume Switch on the DC power supply Selecting a Frequency Adjusting Squelch Selecting Output Power When you finish speaking, release Mic PTTTransmitting Press c/ d to select the appropriate level 1 No Press OK Menu AccessPress MNU to enter Menu mode Menu SET-UP Level Selections Default Menu Configuration Memory channel name See reference Number Store Auto PM Channel StoreChannel Display Memory Channel Lockout Mic VFO Key See reference Visual Scan Automatic Power Off APORemote Control Mic PF Key See reference Mic MR Key RSV report See reference Color for RSV report My call sign See reference Color for call signWhite Message See reference Color for message Packet path See reference Commander call sign See reference Transporter call signSky Command mode Status text transmit rate See reference Offset Programming Flow Operating Through Repeaters Press c / d to select Radio 1-, then press Programming OffsetSelecting Offset Direction Selecting Offset Frequency Press F, T.SEL Activating Tone FunctionSelecting a Tone Frequency Press Tone to activate the Tone function A. and Canada versions Automatic Repeater Offset Transmitting a 1750 Hz Tone Press REV to switch the Reverse function on or OFF Reverse FunctionAutomatic Simplex Check ASC Press Scan to activate the Tone Freq. ID Tone FREQ. ID Memory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing ODD-SPLIT Repeater Frequencies Press M.IN 1 sSelect the desired transmit frequency Press M.IN Clearing a Memory Channel Select band a or B Press MR to enter Memory Recall modePress MHz Tuning control+ Power on Recalling a Memory Channel Repeat steps 6 and 7 to enter up to 8 digits Turn the Tuning control to select the first digitNaming a Memory Channel Press a Press VFO Call ChannelRecalling the Call Channel Reprogramming the Call Channel Channel Display MEMORY-TO-VFO Transfer 440.000 MHz Partial or Full RESET?Parameter Band B Programmable Information Programmable Memory PM Situationit ti Application Examples Recalling a PM Channel Storing in PM Channels PM Channel Reset Press PM+ Power onAuto PM Channel Store Scan Type Scan Range Scan Selecting the Number of Channels Mode 1 31 chMode 2 61 ch Visual Scan Using Visual Scan Press F, Visual to start Visual ScanTo quit Visual Scan, press ESC Selecting Scan Resume Method Time-Operated modeCarrier-Operated mode Seek mode Select band a or B VFO ScanMemory Scan Press VFO 1 s To quit Group Scan, press MHz again Press MHz Tuning control 1 sGroup Scan Locking Out a Memory Channel Setting Scan Limits Program ScanSelect the desired frequency as the lower limit Press F To quit MHz Scan, press MHz again Using Program ScanSelect the appropriate band To quit Program Scan, press VFO again To quit Call/Memory Scan, press Call again CALL/VFO ScanCALL/MEMORY Scan To quit Call/VFO Scan, press Call again Press Tone to activate the Ctcss function Using CtcssContinuous Tone Coded Squelch System Ctcss Press the left or right Band SEL to select band a or B Press Scan to activate the Ctcss Freq. ID Ctcss FREQ. ID Using DCS Digital Code Squelch DCSPress Tone to activate the DCS function Press Scan to activate the DCS Code ID DCS Code ID Manual Dialing Dtmf MonitorFreq. Hz 1209 1336 1477 1633 Repeat steps 4 and 5 to enter up to 8 digits Turn the Tuning control to select a characterAutomatic Dialer Storing a Dtmf Number in Memory Transmitting a Stored Dtmf Number Selecting TX SpeedSelecting Pause Duration VFO PF3 Programmable Function PF KeysPF PF1 MR PF2 Auxiliary Functions Press VFO Press Mic EnterPress the numeric keys in sequence on the keypad Press c/ d to select the desired step size Changing Frequency Step SizeProgrammable VFO Press VFO Press F, Step Auto Dimmer Change Display Contrast Adjust Display DimmerPOSITIVE/ Negative Reversal Automatic Band Change A.B.C Blanking a Band Display Changing MULTI-FUNCTION Button Labels PWR switch MHz SQL controls VOL controlsPress F, MHz to switch the function on or OFF Transceiver Lock Squelch Hang Time Meter Squelch Advanced Intercept Point AIP Changing Beep VolumeSwitching FM/AM Mode KEY Beep ON/ OFF Automatic Power OFF APO TIME-OUT Timer TOT POWER-ON Message Display DemonstrationRepeat steps 3 and 4 to enter up to 8 digits Changing TX/RX Deviation TM-D700E only Changing Speaker ConfigurationsConnection Mode Band a Band B Speaker Mute Microphone Control with MC-53DM only Preparation Wireless Remote Control U.S.A./ Canada only Digits Enter or VFO UP/ Down Access Menu 1-A-3 Control and select onControl Operation Select the receive frequency on band B UHF Freq SKY Command 2 U.S.A./ Canada only TM-D700A Connecting the Transporter with the HF Transceiver 17 r Preparation Flow On Transporter On CommanderProgramming Call Signs Programming a Tone Frequency RIT ON/ OFF XIT ON/ OFF Mic Key Function T y Repeater Function U.S.A./ Canada only Band SEL VS-3 Voice Synthesizer Optional MC-45 MC-53DM MC-80 MJ-88 MJ-89 Optional AccessoriesPS-33 SP-50B VS-3 VC-H1 PG-2N PG-3B PG-4X PG-5A Replace the lower cover 6 screws Installing OptionsInstalling the PG-4X Extension Cable KIT Remove the 6 screws from the lower cover of the main unit Connections Using Two Sets of PG-4X Kits Connections Using One Set of PG-4X Kit Cleaning MaintenanceService Service Note Problem Probable Cause Corrective Action Troubleshooting COM Port VHF Band UHF Band Specifications Sub VHF or UHF band Transmitter Index