Kenwood TS-570D, TS-570S Installation, Antenna Connection, APPROX. Loss dB PER 30 Meters 100 Feet

INSTALLATION

nstall and connect an antenna system {page 1}.

Install a ground system that satisfies DC and RF grounding requirements {page 2}.

Install lightning protection to protect the antenna system, your personal safety, and your property {page 2}.

ANTENNA CONNECTION

The type of the antenna system, consisting of the antenna, ground, and feed line, will greatly affect the successful performance of the transceiver. Use a properly adjusted 50 Ω antenna of good quality to let your transceiver perform at its best. Use a good-quality 50 Ω coaxial cable and a first-quality connector for the connection. Match the impedance of the coaxial cable and antenna so that the SWR is 1.5:1 or less. All connections must be clean and tight.

While the transceiver’s protection circuit will activate if the SWR is greater than 2.5:1, do not rely on protection to compensate for a poorly functioning antenna system. High SWR will cause the transmit output to drop, and may lead to radio frequency interference to consumer products such as stereo receivers and televisions. You may even interfere with your own transceiver. Reports that your signal is garbled or distorted, especially at peak modulation, may indicate that your antenna system is not efficiently radiating the transceiver’s power. If you feel a tingle from the transceiver’s cabinet or the microphone’s metal fittings when you modulate, you can be certain that, at the least, your coax connector is loose at the rear of the radio and, at the worst, your antenna system is not efficiently radiating power.

Connect your antenna feed line to ANT 1. If you are using two antennas, connect the second antenna to ANT 2.

CAUTION:

◆TRANSMITTING WITHOUT FIRST CONNECTING AN ANTENNA OR OTHER MATCHED LOAD MAY DAMAGE THE TRANSCEIVER. ALWAYS CONNECT THE ANTENNA TO THE TRANSCEIVER BEFORE TRANSMITTING.

◆USE A LIGHTNING ARRESTOR TO PREVENT FIRE, ELECTRIC SHOCK, OR DAMAGE TO THE TRANSCEIVER.

1

Install and connect a DC power supply {page 2}.

2

Connect all accessories to the transceiver {pages 3, 60}.

Accessories include the following:		3
• Microphone	• Headphones
• Antenna Tuner	• External Speaker	4
• CW Key	• RTTY Equipment
• Computer	• Linear Amplifier

•TNC/ Multimode Communications Processor

				5
APPROX. LOSS (dB) PER 30 METERS (100 FEET) OF
CORRECTLY MATCHED 50 Ω LINE				6
• Use only as a general guide. Specifications may vary
between cable manufacturers.
				7
Transmission Line	3.5 MHz	14 MHz	30 MHz
RG-174, -174A	2.3	4.3	6.4
				8
RG-58A, -58C	0.75	1.6	2.6
3D-2V	0.80	1.5	2.3
RG-58, -58B	0.65	1.5	2.3
				9
RG-58 Foam	0.70	1.4	2.1
RG-8X	0.50	1.0	2.0
5D-2V	0.45	0.93	1.4	10
RG-8, -8A, -9, -9A, -9B,	0.38	0.80	1.2
-213, -214, -215
5D-FB	N/A	0.80	1.0	11
RG-8 Foam	0.29	0.60	0.90
8D-2V	0.29	0.60	0.90
10D-2V	0.24	0.50	0.72	12
9913	0.24	0.48	0.70
8D-FB	N/A	0.48	0.68
				13
10D-FB	N/A	0.37	0.54
12D-FB	N/A	0.33	0.45
RG-17, -17A	0.13	0.29	0.48
				14
1/2" Hardline	0.12	0.26	0.40
20D-2V	< 0.10	0.25	0.39
3/4" Hardline	< 0.10	0.21	0.32	15
7/8" Hardline	< 0.10	0.16	0.26

N/A: Not available

16

1