OPERATOR CONVENIENCES
1
MICROPROCESSOR RESET
If your transceiver seems to be malfunctioning, resetting the microprocessor default settings may resolve the problem.
The ANT 1/ANT 2 setting will automatically be stored in the current band. Each time you select the same band, the same setting will automatically be selected.
The frequency range of each band is shown below.
2
3
4
INITIAL SETTINGS
For each VFO, the factory defaults for operating frequency and mode are as follows:
•VFO A: 14.000.000 MHz/ USB
•VFO B: 14.000.000 MHz/ USB
The Conventional and Quick memory channels have no data stored.
Frequency Range
(MHz)
0.03~ 2.50
2.50~ 4.10
4.10~ 7.50
7.50~ 10.50
10.50 ~ 14.50
Frequency Range
(MHz)
14.50~ 18.50
18.50~ 21.50
21.50~ 25.50
25.50~ 30.00
30.00~ 60.00
5
6
7
8
PARTIAL RESET
Do Partial Reset if a button or control does not function according to the instructions in this manual. The following are not erased by Partial Reset.
•Memory channel data
•Menu settings
•Antenna tuner preset data
•ANT 1/ANT 2 data.
To do Partial Reset, press [A/B]+ POWER ON.
•“HELLO” appears on the display.
Note: Connect an external antenna tuner to the ANT 1 connector only. After connecting this tuner correctly and selecting ANT 1, the internal tuner will always be bypassed.
FREQUENCY LOCK FUNCTION
Frequency Lock disables some buttons and controls to prevent you from accidentally activating a function or disturbing current settings.
Press [F.LOCK] to toggle Frequency Lock ON or OFF.
•“F.LOCK” appears when the function is ON.
9
10
11
12
13
14
15
16
FULL RESET
Do Full Reset if you want to erase all data in all memory channels. In addition, this function resets all settings, that you customized, to the factory defaults, i.e. menu settings, antenna tuner preset data, etc.
To do Full Reset, press [A=B]+ POWER ON.
•“HELLO” appears on the display.
Note: The IF filter selection in Menu No. 46 will not be reset.
SWITCHING ANT 1/ ANT 2
After connecting antenna feed line to the ANT 1 connector and/or ANT 2 connector on the rear panel, select ANT 1 or ANT 2, depending on which antenna is used for transmitting and receiving.
Press [ANT] to select ANT 1 or ANT 2.
•“ANT 1” or “ANT 2” appears to show which antenna is selected.
The following buttons and controls are disabled by Frequency Lock:
• | Tuningcontrol |
|
| • | MULTI/CHcontrol | |
• QUICK MEMO [MR] | • QUICK MEMO [M.IN] | |||||
• | [FINE] | • | [REV] |
| • | [CLR] |
• | [ENT] | • | [LSB/USB] | • | [CW/FSK] | |
• | [FM/AM] | • | [1MHz] |
| • | [UP]/[DOWN] |
• | [SPLIT] | • | [A/B] |
| • | [M/V] |
• | [A=B] | • | [SCAN] |
| • | [M>VFO] |
• | [M.IN] |
|
|
|
|
|
Note:
◆After activating Frequency Lock, the MULTI/CH control and [UP]/[DOWN] are still available in Menu mode.
◆After activating Frequency Lock, you can still change the transmit frequency with the Tuning control while using the
◆After activating Frequency Lock, the MULTI/CH control is still available for selections other than frequency and memory channel changes.
◆After activating Frequency Lock, [CLR] is still available in some situations.
48
