7528%/(6+227,1*
Problem |
| Probable Cause |
| Corrective Action | Page |
VOX does not | The VOX gain is set too low. | Increase the VOX gain. | 30 | ||
operate. |
|
|
|
|
|
HF/ 50 MHz Linear | 1 | The linear amplifier control | 1 | Set Menu No. 53 (HF) or 54 (50 MHz) to 1, 2, | 53 |
amplifier does not |
| is OFF. |
| or 3. |
|
operate. | 2 | The REMOTE connector | 2 | Inspect the REMOTE connector wiring and | 66 |
|
| wiring is wrong or faulty. |
| correct it as necessary. |
|
|
|
|
|
|
|
The transceiver’s | 1 | The air filters for the cooling | 1 | Contact a Kenwood authorized service | — |
output power |
| fans have been congested |
| center to clean the filters. |
|
decreases after a |
| with dust. |
|
|
|
short operating time. | 2 | The cooling fans cannot | 2 | Relocate the transceiver so that air can easily | — |
|
| provide enough air flow to |
| flow through the |
|
|
| cool the transceiver down. |
| cooled. |
|
|
|
|
|
|
|
You cannot access | 1 | Many repeaters require a | 1 | Review “FM REPEATER OPERATION” and | 25 |
and use repeaters. |
| subtone or 1750 Hz tone to |
| select the correct frequency and type of |
|
|
| access. |
| subtone. | 25 |
| 2 | Transmission and/or | 2 | You must transmit on the repeater’s input | |
|
| reception frequency is |
| frequency and receive on the repeater’s |
|
|
| wrong. |
| output frequency. Refer to “FM REPEATER |
|
|
|
|
| OPERATION”. |
|
|
|
|
|
|
|
Digital operation | 1 | Physical connections | 1 | 67,69 | |
results in few or no |
| between the transceiver, |
| your TNC/ MCP manual, and your computer |
|
connects or contacts |
| computer, and TNC/ MCP |
| hardware manual as references. |
|
with other stations. |
| are incorrect, or software |
|
|
|
|
| settings in the TNC/ MCP |
|
|
|
|
| are wrong. |
|
|
|
| 2 | Different transmission and | 2 | Confirm that the RIT and XIT functions are | 29,31 |
|
| reception frequencies are |
| switched OFF. Confirm that you are not |
|
|
| being used. |
| operating split frequency. |
|
| 3 | The levels between the | 3 | Adjust TX and RX levels using Menu Nos. | 58,69 |
|
| transceiver and the TNC/ |
| 66 and 67, and level controls on your TNC/ |
|
|
| MCP are incorrect. |
| MCP. |
|
| 4 | Your transmitted signal or | 4 | Reorient/ relocate your antenna or increase | 1 |
|
| the incoming receive signal |
| your antenna gain. |
|
|
| is too weak. |
|
|
|
| 5 | The TX delay time | 5 | Set the TNC/ MCP TX delay time to more | — |
|
| parameter in your TNC/ |
| than 300 ms. |
|
|
| MCP was incorrectly set. |
|
|
|
|
|
|
|
|
|
Attempts at controlling | 1 | Problem with cable that | 1 | Check the cable and cable connections. | 67 |
the transceiver with |
| connects the PC to the |
|
|
|
the computer have |
|
|
|
| |
failed. | 2 | Communication parameters | 2 | Use the same parameters in the terminal and | 57 |
|
| set in your terminal |
| the transceiver. Check Menu Nos. 61 and |
|
|
| program do not match the |
| 62. |
|
|
| transceiver parameters. |
|
|
|
A sensor in the transceiver | Stop transmitting and let the transceiver | — | |||
and “CHECK” in | detected high temperature. | cool down for a while. Contact a Kenwood |
| ||
Morse code sounds. |
|
| authorized service center to clean the internal air |
| |
|
|
| filters. |
| |
|
|
|
| ||
Transmission | The voltage of the DC power | Adjust the DC power supply voltage to | 1 | ||
suddenly stops. | supply is too high. | 13.8 V DC. |
| ||
“DSP ERR x” appears | An internal DSP error occurs. | Restart the transceiver by turning the power | — | ||
(where x is a number |
|
| OFF and then back ON. If the problem persists, |
| |
from 0 ~ 3). |
|
| consult Kenwood authorized Service Center. |
| |
|
|
|
| ||
“VGS ERR” appears. | An internal error occurred in | Confirm that the connector of the | 71 | ||
| the | securely connected to the transceiver, then |
| ||
|
|
| turn the transceiver power OFF and ON. If the |
| |
|
|
| problem persists, contact a Kenwood authorized |
| |
|
|
| service center for repairs. |
| |
|
|
|
|
|
|
77
