Kenwood TS-590S instruction manual 81&7,21, Mode Morse Code Output, Beep Type Meaning

23(5$725&219(1,(1&(6

The table below is an example of setting the Auto Mode frequency.

Channel	Frequency	Mode	Operation Range
No.	(MHz)			(MHz)
00	1.620	AM	0.030	”I	1.620
01	2.000	CW	1.620	”I	2.000
02	3.500	LSB	2.000	”I	3.500
03	3.525	CW	3.500	”I	3.525
04	10.100	LSB	3.525	”I	10.100
05	10.150	CW	10.100	”I	10.150

0614.000 USB 10.150 ”I 14.000

0714.070 CW-R 14.000 ”I 14.070

0814.112 FSK 14.070 ”I 14.112

0918.068 USB 14.112 ”I 18.068

10	18.110	CW	18.068	”I	18.110
11	21.000	USB	18.110	”I	21.000
12	21.070	CW	21.000	”I	21.070
13	21.125	FSK-R 21.070 ”I 21.125
14	21.150	CW	21.125	”I	21.150
15	24.890	USB	21.150	”I	24.890
16	24.930	CW	24.890	”I	24.930
17	28.000	USB	24.930	”I	28.000
18	28.070	CW	28.000	”I	28.070
19	28.150	FSK	28.070	”I	28.150
20	28.200	CW	28.150	”I	28.200

2129.000 USB 28.200 ”I 29.000

2230.000 FM-DATA 29.000 ”I 30.000

2350.000 USB 30.000 ”I 50.000

24	50.100	CW	50.000	”I	50.100
25	51.000	USB	50.100	”I	51.000
26	52.000	FM	51.000	”I	52.000

2752.000 LSB

2852.000 LSB

2952.000 LSB

3052.000 LSB

3152.000 LSB

•The frequencies for channels 27 ~ 31 have not been configured, but because they are the same frequency as channel 26, they will be FM mode

0+]”I0+]

•Since the frequencies above 52.0 MHz have not been configured, they will be USB mode

0+]”I0+]

%((3)81&7,21

The Beep function provides you confirmation of entry, error status, and malfunctions of the transceiver.

Although you can turn the beep function OFF by accessing Menu No. 03, we recommend you leave it ON in order to detect unexpected errors and malfunctions. You can also change the output level of the beeps by accessing Menu No. 03 and selecting “1” to “9”.

The transceiver generates the following Morse code to tell you which mode is selected when you change operating modes:

Mode	Morse Code Output
USB	• • –	(U)
LSB	• – • •	(L)
CW	– • – •	(C)
FSK	• – •	(R)
AM	• –	(A)
FM	• • – •	(F)
USB-DATA	• • – – • •	(UD)
LSB-DATA	• – • • – • •	(LD)
CW-R	– • – • • – •	(CR)
FSK-R	• – • • – •	(RR)
FM-NAR	• • – • • –	(FN)
FM-DATA	• • – • – • •	(FD)
FM-NAR-DATA	• • – • – • – • •	(FND)

The transceiver also generates the following warning, confirmation, and malfunction beeps.

Beep Type	Meaning
Short, high pitch	A valid key is pressed.
Double, high pitch	A secondary function is selected.
3 times, high pitch	The third function is accepted.
Long, high pitch	A key entry is accepted, Scan
	starts, or AT tune has completed.
Short, regular	A function is turned OFF.
Short, low pitch	An invalid key is pressed.
Morse “UL”	The internal PLL circuit unlock
	status is detected.
Morse “S”	CW Auto Tune cannot complete,
	or an invalid frequency is entered.
Morse “5”	AT Tune cannot be completed
	within the specified time.
Morse “SWR”	The antenna’s SWR is too high
	(over 10:1) to perform AT tune.
	1 minute before the APO (Auto
	Power Off) function switches the
Morse “CHECK”	transceiver OFF, a protection
	circuit is ON. or an invalid
	voltage is detected.
	Waiting for a CW message to be
Morse “BT”
	recorded.
	The current message memory
Morse “AR”
	is full.

52