Kenwood TS-590S 0025$7856 00255&$//$16&52, 002575$165,  0HPRU\5HFDOO,  0HPRU\6FUROO

0(025<)($785(6

0(025<5(&$//$1'6&52// Q 7HPSRUDU\)UHTXHQF\&KDQJHV

There are 2 modes which allow you to retrieve frequencies and associated data that you stored in a memory channel: Memory Recall and Memory Scroll.

Q 0HPRU\5HFDOO

In this mode, the transceiver receives and transmits using a frequency that you retrieve. You can temporarily change the frequency and associated data without overwriting the contents of the memory channel when Menu No. 18 is ON (default is OFF).

1Press [M/V] to enter Memory Recall mode.

•The memory channel that was last selected appears.

After retrieving frequencies and associated data in Memory Recall mode, you can temporarily change the data without overwriting the contents of the memory channel.

1Access Menu No. 18 and select “on”.

•Skip this step when changing only the associated data (not the frequency).

2Recall a memory channel.

3Change the frequencies and associated data.

•Use only the Tuning control to select a frequency.

4If necessary, for future use, store the changed data in another memory channel. Refer to “Channel ° Channel Transfer” {below}.

Note: If Menu No. 18 is set to “on”, the frequency of the memory channel can be changed.

2Turn the MULTI/CH control, or press Mic [UP]/ [DWN] to select a memory channel.

•Continuously holding down Mic [UP]/ [DWN] steps the transceiver through the memory channels until the key is released.

•Memory channels which contain no data are skipped.

•You cannot change memory channels while transmitting.

3To exit Memory Recall mode, press [M/V].

Note: If Menu No. 18 is set to “on”, the frequency of the memory channel can be changed.

Q 0HPRU\6FUROO

Use this mode to check the contents of the memory channels without changing the current reception frequency. In this mode, frequencies you retrieve are not used for receiving and transmitting.

1Press [M.IN] to enter Memory Scroll mode.

•The memory channel that was last selected appears.

2Turn the MULTI/CH control, or press Mic [UP]/ [DWN] to step through the memory channels.

•You can also change channels by entering a 2-digit number. Press [ENT], [24 (8)], [28 (9)] for example.

3To exit Memory Scroll mode, press [CLR].

•The transceiver re-displays the memory channel or VFO frequency that was selected before you activated Memory Scroll.

Note: Do not press [M.IN] again after entering Memory Scroll mode. Pressing [M.IN] results in over-writing the current VFO data to the memory channel you selected.

0(025<75$16)(5

Q 0HPRU\°9)27UDQVIHU

After retrieving frequencies and associated data from Memory Recall mode, you can copy the data to the VFO. This function is useful, for example, when the frequency you want to monitor is near the frequency stored in a memory channel.

1Recall the desired memory channel.

2Press [M>V].

•When a simplex channel is recalled, the data is copied to VFO A or VFO B, depending on which VFO was used to recall the channel.

•When a split channel is recalled, the RX data is copied to VFO A and the TX data is copied to VFO B.

Note: Pressing [M>V] after temporarily changing the retrieved data copies the new data to the VFO.

Q &KDQQHO°&KDQQHO7UDQVIHU

You can also copy channel information from one memory channel to another. This function is useful when storing frequencies and associated data that you temporarily change in Memory Recall mode.

1Recall the desired memory channel.

2Press [M.IN] to enter Memory Scroll mode.

• To exit Memory Scroll mode, press [CLR].

3Select the memory channel where you would like the data copied, using the MULTI/CH control.

4Press [M.IN].

42