12. Sampling and playing motion video

You can sample a motion video clip and play it back while using an effect program and the touch-pad to control the video clip (for example by expanding or inverting it).

If you have selected a program from the SAMPLE/ PLAY group, you can use the touch-pad to control the playback speed of the video, or even reverse the playback.

The sampled video will be lost when you turn off the power. It is not possible to save the sampled video.

Sampling

1.Select program 94–99 from the “SAMPLE/ PLAY” group.

2.When you press the [REC/STOP] key, the [REC/STOP] key will light and recording will begin. Recording will end when you

press the key again or when the memory capacity has been reached.

If you select an effect clip pattern (40–59) in pattern display mode, you will be able to record a pattern. Turn on the [SAMPLE 1] or [SAMPLE 2] key to record the still image that you sampled.

Playback

The playback method will depend on the effect program you have selected.

For a program in the “SAMPLE/PLAY” group

1.Select a program in the “SAMPLE/PLAY” group.

2.When you touch the touch-pad, the video clip will play back according to the position of your finger on the touch-pad.

For a program not in the “SAMPLE/PLAY” group

1.Select a program not in the “SAMPLE/ PLAY” group.

2.With the [SAMPLE 1] and [SAMPLE 2] keys turned off, hold down the [REC/STOP] key and touch the touch-pad; the sampled video clip will playback at normal speed. If you hold down the [REC/STOP] key and press the [HOLD] key, the [REC/STOP] key will be held, allowing you to play back the video clip simply by touching the touch-pad. Hold will be cancelled when you press the [REC/ STOP] key once again.

When you hold down the [REC/STOP] key and press the [HOLD] key, playback will be held. When you press the [REC/STOP] key

once again, the hold will be cancelled. Pattern display will be cancelled if you play back a motion video sample while a pattern is displayed.

You cannot display a pattern during sample playback.

13. Sampling and playing a phrase

If you have recorded a phrase from the input into the [SAMPLE 1] and [SAMPLE 2] keys, you can select a program from the “SAMPLE/PLAY” group (90–99) and use the touch-pad to control the playback speed or reverse playback.

If you have selected a program from other than the “SAMPLE/PLAY” group, pressing the [SAMPLE 1] or [SAMPLE 2] key will play back the phrase that was recorded on each key. You can record approximately six seconds of monaural sound in each key.

The recorded phrase will be lost when you turn off the power. It is not possible to save the recorded phrase.

Recording

1.Press the [REC/STOP] key. The [REC/STOP] key LED will blink, and you will be in record-ready mode.

2.Press either the [SAMPLE 1] or [SAMPLE 2] key that you want to use for recording. The playback audio will not be heard at this time.

3.Press the [REC/STOP] key; the [REC/STOP] key LED will light and recording will begin. Recording will end when you press the [REC/STOP] key once again.

Recording will end automatically if you record up to the maximum recording time.

If you select a program not in the “SAMPLE/ PLAY” group, you can operate the touch-pad while you record; the sound processed by the effect will be recorded.

Auto-rec (AUTO REC)

You can make recording start automatically when audio is input to the [INPUT] audio jacks.

1.In step 2 of recording, hold down the [SAMPLE 1] or [SAMPLE 2] key you want to use, and press the [REC/STOP] key; the [REC/STOP] key and [SAMPLE 1] [SAMPLE 2] key LEDs will blink simultaneously, and you will be in record-ready mode.

2.When you input an audio signal, recording will begin automatically. Recording will end when you press the [REC/STOP] key once again.

If the lever is set to “COMBI,” and you have selected a program from the “SAMPLE/PLAY” group as the video effect, you can record the video simultaneously with the audio.

9