Manuals / Kramer Electronics / Computer Equipment / Computer Accessories

Kramer Electronics VP-81KSi user manual Installing in a Rack

Models: VP-81KSi

1 51

Download 51 pages 495 b

Page 12

Installing in a Rack

Installing in a Rack

5Installing in a Rack

This section describes the preparation and installation of the unit in a rack.

.

8	KRAMER: SIMPLE CREATIVE TECHNOLOGY

Image 12

Kramer Electronics VP-81KSi user manual Installing in a Rack

Contents

8x1 UXGA/Audio STEP-IN Switcher USER MANUALModel VP-81KSiContents Figures Switching Protocols via the Front Panel ButtonsSwitching Protocols via Protocol Commands Command Part DetailsTables 1 Introduction 2 Getting StartedOne SI-1VGA Remote Step-in Module and user manual2 2.1 Quick StartGetting Started KRAMER SIMPLE CREATIVE TECHNOLOGY3 Overview 3.1 Defining EDID 4 Defining the VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher Defining the VP-81KSi 8x1 UXGA/Audio STEP-IN SwitcherFigure 1 VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher Front Panel Table 1 VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher Front Panel FeaturesFigure 2 VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher Rear Panel Table 2 VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher Rear Panel Features4.1 Using the IR Transmitter for the VP-81KSi 1 Model C-A35M/IRR-50 2 Model C-A35M/A35F-50 3 P/N 505-70434010-S5 Installing in a Rack Installing in a Rack6 Connecting the VP-81KSi 8x1 UXGA/Audio STEP-IN Switcher To connect1 the VP-81KSi, as illustrated in the example in Figure6.1 Connecting the Balanced/Unbalanced Stereo Audio Output 6.2 Connecting Remote Contact Closure Input Selection Switches 6.3 Connecting the SI-1VGA Remote Step-in Module6.4 Connecting the AV ON CAT 5 Twisted Pair Output 6.5 Connecting to the VP-81KSi via the RS-232 PortTo connect to the VP-81KSi via RS-232 6.6 Connecting to the VP-81KSi via the RS-485 Port To connect a device with a RS-485 port to the VP-81KSi6.7 Cascading Multiple VP-81KSi Devices To daisy-chain up to eight VP-81KSi devicesTo cascade up to eight VP-81KSi devices 6.8 Controlling a Remote RS-232 Device 6.9 Connecting to the VP-81KSi via the Ethernet Port To connect the VP-81KSi directly to a PC2. On the PC, click Start Control Panel 3. Double-click Network Connections5. Select Internet Protocol TCP/IP see Figure 6. Click the Properties button8. Click OK Figure 10 Local Area Connection Properties WindowTo configure the VP-81KSi Ethernet port 7.1 Using the Front Panel INPUT SELECTOR Buttons 7 Operating the VP-81KSi Locally via the Front Panel Buttons7.2 Using the Audio-Follow-Video/Breakaway Modes 7.3 Setting the Audio Output Gain7.4 Operating Cascaded VP-81KSi Devices To switch to AFV Audio Follow Video modeOperating the VP-81KSi Remotely using a Web Browser Operating the VP-81KSi Remotely9.1 To Log On to the VP-81KSi Web Pages To log on to VP-81KSi Web pages9.2 The Switching Matrix Page To switch an input to an output for example, input 4 to output To operate in the Confirm mode 9.3 The Audio Gain Page To change an input or output gain9.4 The Configurations Page 1. Click CONFIGURATIONS10 Upgrading the Firmware 11 EDIDUpgrading the Firmware 12 Technical Specifications Table 6 lists the technical specifications1 of the VP-81KSiTable 6 Technical Specifications of the VP-81KSi 14 Default EDID 13 Communication ParametersThe default EDID is stored in all inputs Table 7 Communication Parameters15 Table of ASCII Codes for Serial Communication Protocol Table of ASCII Codes for Serial Communication Protocol16 Table of Hex Codes for Serial Communication Protocol 17 Kramer Protocol 17.1 Switching Protocols 17.2 Kramer Protocol#P2000CR 0x38, 0x80, 0x8317.2.2 Command Part Details CommandCommands chain separator char ParametersCommands entering Commands formsCommands chaining Table 16 Instruction Codes for ProtocolKramer Protocol 0 or off for not existent signal. 1 or on for existent signal Read video connections~PRST-RCL 3 OK Show source of video output 2 fromRead audio volume level In,Out orCHANNEL = Input or Output # decrease current valueMACHINENAME = Up to 14 Alfa-Numeric chars Machine factory name = Model name + last 4 digits from serial numberNEWMACHINENUMBER @MACH-NUM OLDMACHINENUMBER ,NEWMACHINENUMBER OK 17.3 Kramer Protocol Kramer ProtocolTable 17 Protocol Definitions Table 18 Instruction Codes for Protocol Bit 7 - Defined asI6…I0 - “INPUT” O6…O0 - “OUTPUT”Kramer Protocol INSTRUCTIONDEFINITION FOR SPECIFIC INSTRUCTION DESCRIPTIONie. VIS setting = 1, which is defined as VIS from input #1 Kramer Protocol 81 i.e. 128dec+ ASCII for “Y” 128dec+ ASCII for “C”82 ie. request the number of outputs ie. 16 outputsOnly the first purchase customer may enforce this warranty Safety Warning P/N 2900-657 REVP/N 2900