Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCR2584 Dual Tailwheel, Trail-Type Lift Selections, Table of Contents, Adjustments

Models: RCR2584

1 32

Download 32 pages 688 b

Page 20

Dual Tailwheel

Table of Contents

Section 3 Adjustments

Land Pride

Dual Tailwheel

Refer to Figure 3-5:

1.If the cutting height is too high or too low, the tailwheel must be adjusted as follows:

a. Use the tractors 3-point hydraulic control to lift the

cutter such that the tailwheel clears the ground surface.

b.Remove attaching hardware; 1/2” -13 x 3 1/2" long bolt (#1), 1/2” lock washer (#2) and 1/2” nut (#3).

c.Adjust the tailwheel up or down to the desired cut- ting height and replace the attaching hardware.

14388

Dual Tailwheel Height Adjustment

Figure 3-5

Trail-Type Lift Selections

The trail-type unit can be equipped with a ratchet jack (#1), or hydraulic cylinder (#2). The hydraulic selection includes stroke control spacers (#3) to set cutting height. Stroke control spacers (#3) consist of cast steel halves and a

spring clip. To install or remove, simply raise or lower im- plement with tractor hydraulics and pull stroke control valves apart. Store stroke control spacers on hydraulic hose (#4) near hydraulic cylinder. Refer to Figure 3-6.

Trail-Type Lift Selections

Figure 3-6	14390

18 RCR2584 Rotary Cutter 312-459M

7/14/08

Image 20

Land Pride RCR2584 manual Dual Tailwheel, Trail-Type Lift Selections, Table of Contents, Adjustments, Refer to Figure

Contents

Table of Contents Rotary CutterOperator’st ’s Manuall Copyright 2008 Pr intedTable of Contents Important Safety InformationSection 1 Assembly and Setup Section 3 AdjustmentsImportant Safety Information Be Aware of Signal WordsKeep Riders Off Machinery For Your ProtectionUse Safety Lights and Devices Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentImportant Safety Information Table of ContentsSafety at All Times 1. Keep all safety labels clean and legible 5. To install new labelsa. Clean the area on which the label is to be placed 818-130C818-230C 818-540C818-552C Table of Contents818-830C 838-094CTable of Contents Important Safety InformationUsing This Manual Owner AssistanceIntroduction Serial Number PlateSection 1 Assembly and Setup 3-Point Hitch Assembly3-Point Quick Hitch Assembly Driveline InstallationSingle Tailwheel Assembly Dual Tailwheel AssemblyTable of Contents Section 1 Assembly and SetupHitch Assembly Trail-Type CutterTable of Contents Section 1 Assembly and SetupSafety Guards Axle AssemblyDANGER Rear Chain GuardTractor Hook-Up 3-Point Tractor Hook-UpTable of Contents Section 1 Assembly and SetupTrail-Type Tractor Hook-Up Table of ContentsSection 1 Assembly and Setup Refer to FigureSafety Chains Check ChainsTable of Contents Section 1 Assembly and SetupOperating Checklist TransportingOperating Check List Cutting InstructionsLeveling Procedure Section 3 AdjustmentsLift-Type Cutter Nominal Cutting HeightCutter Height Adjustment Single TailwheelTable of Contents Section 3 AdjustmentsDual Tailwheel Trail-Type Lift SelectionsTable of Contents Section 3 AdjustmentsDeck Attitude Adjustment Lift-TypeTrail-Type Table of ContentsMaintenance Service Cutting BladesSection 4 Maintenance and Lubrication Clutch Run-InClutch Assembly and Disassembly StorageTable of Contents Section 4 Maintenance and LubricationLubrication LubricationTailwheel Spindle Tube Tailwheel HubDriveline U-Joints DrivelineRatchet Jack Inner Tube BearingTable of Contents Section 5 Speciﬁcations and CapacitiesRCR2584 Rotary Cutter Bent Driveline NOTE driveline should Section 6 TroubleshootingTable of Contents Driveline bent Table of ContentsSection 6 Troubleshooting Torque Values Chart for Common Bolt Sizes Section 7 AppendixTable of Contents Land PrideTable of Contents Section 7 AppendixLand Pride 28 RCR2584 Rotary Cutter 312-459MWarranty Table of ContentsSection 7 Appendix Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Ofﬁce P.O. Box 5060 Salina, Kansas 67402-5060 USA