Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCR2584 Lubrication, Tailwheel Spindle Tube, Tailwheel Hub, Gearbox, Table of Contents

Models: RCR2584

1 32

Download 32 pages 688 b

Page 24

Lubrication

Table of Contents

Section 4 Maintenance and Lubrication

Land Pride

Lubrication

Lubrication

Legend

Multipurpose	Multipurpose	Multipurpose	50
spray lube	grease lube	oil lube	50

Intervals at which lubrication is required

13753

13753

14269

24

Tailwheel Spindle Tube

Type of Lubrication: Grease

Quantity = 6 pumps

8

Tailwheel Hub

The tailwheel hub is equipped with a relief hole located directly opposite the grease ﬁtting. The relief hole re- leases pressure from inside the hub casting when it is greased. The hub should be greased until grease purg- es from the relief hole.

Type of Lubrication: Multipurpose Grease

Quantity = Until grease purges from the relief hole

8

Gearbox

Check oil level in the gearbox by removing the side plug in the gearbox case. If the oil level is low, remove the top plug in the gearbox case and ﬁll with EP90 oil until oil ﬂows from the side port of gearbox case. Reinstall plugs and tighten.

NOTE: Do not overﬁll! Cutter should be level when checking oil.

Type of Lubrication: EP90 Oil

Quantity = ﬁll until oil ﬂows from the side port of gearbox case.

22 RCR2584 Rotary Cutter 312-459M

7/14/08

Image 24

Land Pride RCR2584 manual Lubrication, Tailwheel Spindle Tube, Tailwheel Hub, Gearbox, Table of Contents

Contents

Table of Contents Rotary CutterOperator’st ’s Manuall Copyright 2008 Pr intedTable of Contents Important Safety InformationSection 1 Assembly and Setup Section 3 AdjustmentsImportant Safety Information Be Aware of Signal WordsKeep Riders Off Machinery For Your ProtectionUse Safety Lights and Devices Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentTable of Contents Safety at All TimesImportant Safety Information 1. Keep all safety labels clean and legible 5. To install new labelsa. Clean the area on which the label is to be placed 818-130C818-230C 818-540C818-552C Table of Contents818-830C 838-094CTable of Contents Important Safety InformationUsing This Manual Owner AssistanceIntroduction Serial Number PlateSection 1 Assembly and Setup 3-Point Hitch Assembly3-Point Quick Hitch Assembly Driveline InstallationSingle Tailwheel Assembly Dual Tailwheel AssemblyTable of Contents Section 1 Assembly and SetupHitch Assembly Trail-Type CutterTable of Contents Section 1 Assembly and SetupSafety Guards Axle AssemblyDANGER Rear Chain GuardTractor Hook-Up 3-Point Tractor Hook-UpTable of Contents Section 1 Assembly and SetupTrail-Type Tractor Hook-Up Table of ContentsSection 1 Assembly and Setup Refer to FigureSafety Chains Check ChainsTable of Contents Section 1 Assembly and SetupOperating Checklist TransportingOperating Check List Cutting InstructionsLeveling Procedure Section 3 AdjustmentsLift-Type Cutter Nominal Cutting HeightCutter Height Adjustment Single TailwheelTable of Contents Section 3 AdjustmentsDual Tailwheel Trail-Type Lift SelectionsTable of Contents Section 3 AdjustmentsDeck Attitude Adjustment Lift-TypeTrail-Type Table of ContentsMaintenance Service Cutting BladesSection 4 Maintenance and Lubrication Clutch Run-InClutch Assembly and Disassembly StorageTable of Contents Section 4 Maintenance and LubricationLubrication LubricationTailwheel Spindle Tube Tailwheel HubDriveline U-Joints DrivelineRatchet Jack Inner Tube BearingSection 5 Speciﬁcations and Capacities RCR2584 Rotary CutterTable of Contents Section 6 Troubleshooting Table of ContentsBent Driveline NOTE driveline should Table of Contents Section 6 TroubleshootingDriveline bent Torque Values Chart for Common Bolt Sizes Section 7 AppendixTable of Contents Land PrideTable of Contents Section 7 AppendixLand Pride 28 RCR2584 Rotary Cutter 312-459MWarranty Table of ContentsSection 7 Appendix Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Ofﬁce P.O. Box 5060 Salina, Kansas 67402-5060 USA