Installer Menu (Cont.)
011 - KEY DEFEAT (Keyboard Defeat)
If set to 1, KEY DEFEAT prevents the end user from accessing the
Note: Users can always access the menus by pressing MENU on the remote.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers.
Note: Clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.
Note: Clock must be set before the Alarm function will work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on “bed number” in a
Values | IR Mode | Bed # |
0 | Disabled | N/A |
|
|
|
Note: For further information, see documentation for the accessory package that includes the
021 -
Set to 1 to activate
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting configured before the TV was turned OFF when the TV is turned ON.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.
029 - OLD OCV (On Command Video™)
Set to 1 for operation with systems from On Command Corporation.
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI.
032 - TIMING PULSE
MPI Communication Parameter. Sets baud rate for MPI. Step size of 4.3 uS. Changing from default may affect communication via MPI.
035 - HDMI1 ENABLE
Set to 1 or 2 (if available) to enable display panel HDMI 1 input. If value 2 is available, value 1 selects Over Scan and value 2 selects Just Scan. Otherwise, HDMI 1 input is enabled with auto detection when value 1 is set. Set to 0 to disable display panel HDMI 1 input.
Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.
041 - SIMPLINK EN
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable SIMPLINK functionality without enabling remote control access to the SIMPLINK Menu. Set to 2 to enable both SIMPLINK function- ality and SIMPLINK Menu access, though note that the Speaker menu option will be inaccessible/grayed out. Set to 3 to enable all aspects of SIMPLINK feature and SIMPLINK Menu. If a home theater device is connected to the TV, users can select either the TV or HT (home theater) speaker.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = Video 1 | 4 | = RGB | 7 = HDMI 3 |
3 = HDMI 1 | 5 | = HDMI 2 | 255 = Last Aux |
Note: Above is applicable only if all Aux sources are enabled.
Note: This item is not available in the Installer Menu unless item 004 STRT CHANNEL is set to 0.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change. Controls MPI status channel response for Aux inputs.
23 |