LG Electronics 55LS675H LT2002 Cloning Notes, Clone Programmer Cloning Procedures Cont, MPI Cable

Models: 37LT670H 26LT670H 42LT670H 55LS675H 32LT670H

1 68
Download 68 pages 22.8 Kb
Page 35
Image 35
LT2002 Cloning Notes

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

LT2002 Cloning Notes

• Read the IMPORTANT CLONING

INFORMATION on page 28 before

beginning any cloning procedures.

• A slow flashing green light indicates

that there are communication

Antenna

or CATV

MPI

Cable

 

problems between the TV and the

 

LT2002. If this is the case, check for

 

a damaged cable, poor contacts, or

 

other connection troubles.

If the status indicator is red, the

 

LT2002 batteries are low and should

 

be replaced. Install four (4) high-

 

quality alkaline AA batteries.

Learning and Teaching is only

 

possible between identical model TVs;

 

however, the LT2002 can store up to

 

three different Master TV Setups.

Learn Setup from Master TV

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION

XX

THE SW IS REVISION

XX

CLONE CLOCK = XX:XX

 

TV

CLOCK = XX:XX

 

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Ferrite Core (TDK, ZCAT 2035-0930)

LT2002 Clone Programmer

Connect cable to

 

 

 

 

 

 

TV MPI Jack and

 

Status

follow on screen

 

instructions

 

Indicator

 

MPI

 

 

 

 

 

 

 

 

 

 

 

Reset

 

 

 

 

Color

 

• green

 

battery ok

 

• red

 

battery low

 

 

 

Blink pattern

 

 

• slow

 

power on

no communications

• heartbeat power on communications ok

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

1.Ensure the Master TV is set up completely and in Pass-through Mode.

2.Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port.

3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press OK to proceed to the Memory Bank Selection Menu.

5.Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press OK.

CLONE SELECTION MENU

MPI (1) LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

SAVE TV SETUP IN SELECTED

CLONE MEMORY

Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

6.Verify the Learning setup information on the next screen, and then press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup. When the Learning process is complete, a “LEARNING COMPLETE” message will be displayed.

7.When Learning is complete, disconnect the MPI cable from the Master TV.

(1)MEMORY 1 VER XX REV XX

(2)MEMORY 2 VER XX REV XX

(3)MEMORY 3 VER XX REV XX

(4)RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

206-4213

35

Page 35
Image 35
LG Electronics 55LS675H LT2002 Cloning Notes, Clone Programmer Cloning Procedures Cont, Learn Setup from Master TV