Manuals / Liebert / Computer Equipment / Network Card

Liebert LDM user manual Upgrading the Firmware

Models: LDM

1 40

Download 40 pages 23.25 Kb

Page 34

5.6Upgrading the Firmware

Operation

5.6Upgrading the Firmware

The Flash program is used to upgrade the firmware on a Liebert LDM unit. It uses the service termi- nal port to erase the old firmware, copy the new firmware and reboot the unit.

NOTE

Updating the firmware will not erase any configuration settings currently installed. No notice is given to customers when a new firmware version becomes available. Check Liebert’s Web site periodically for any available updates (see 5.3 - Downloading the Software).

To upgrade the firmware:

1.Make sure the Liebert LDM unit is powered ON.

2.Connect the PC to the Liebert LDM via the external DB9 connection. Refer to 5.2.1 - LDM Setup Port Connection.

3.If needed, download the latest version of the software (see 5.3 - Downloading the Software).

4.Run the file named Flash x.x.x.exe (where x.x.x is the version number).

5.In the Upgrade Firmware window, click the Select Port button.

6.In the Scan for LDM Units window:

•Select the COM port from the drop-down list—for example, COM1.

•Make sure the Baud Rate is 115200.

•Click the Start Scan button to check for a connection to the unit.

30

Image 34

Liebert LDM user manual Upgrading the Firmware

Contents

User Manual Liebert Distribution Monitoring LDMAC Power For Business-Critical ContinuityPage 4.0 INSTALLATION TABLE OF CONTENTSSAFETY INSTRUCTIONS 1.0 GLOSSARY OF ABBREVIATIONS 2.0 PRODUCT OVERVIEW 3.0 MAJOR COMPONENTS5.5 Using the Configuration Tool TABLES5.6 Upgrading the Firmware SAFETY INSTRUCTIONS The following abbreviations are used in this manual 1.0 GLOSSARY OF ABBREVIATIONSGlossary of Abbreviations 2.0 PRODUCT OVERVIEW Product Overview3.1 Branch Circuit Monitoring Control Board BCB 3.0 MAJOR COMPONENTS3.2 Panel Board Voltage-Current Board PBVI CT matrix for the Liebert LDM3.3 Large Interface Board LIB 3.5 Power Supply Assembly with EMI Filter3.4 Branch Circuit Monitoring Sensor Module BSM 4.0 INSTALLATION 4.1 Installing a BSM CT Module Assembly4.1.1 Connecting Panelboards A and B 4.2 Installing a Solid-Core Current Transformer One LIB can support up to eight output and/or subfeed breakers4.3 Connecting a Current Transformer to the PBVI Board Wiring configuration of large branch circuit breakers 4.4 CT Table for PBVI BoardInstallation Wiring configuration of large branch circuit breakers continued Installation4.5 Connecting a Current Transformer to the LIB Board Wiring configuration for LIB 4.6 CT Table for LIBInstallation Wiring configuration for LIB2 Installation5.0 OPERATION Table 5 Parameters monitored for breakers5.1 Alarms Alarm conditions and factory setpoints5.2.2 Modbus Connection 5.2.1 LDM Setup Port Connection5.2 Communication The triangle printed on the circuit board depicts Pin5.4.1 Starting the Monitor Tool 5.4 Using the Monitor Tool5.3 Downloading the Software Monitoring - see 5.4 - Using the Monitor Tool5.4.3 Panel Status and Real-Time Clock 5.4.2 Monitor Menu OptionsMonitor menu options 5.4.5 Breaker Status 5.4.6 Mode Buttons5.4.4 Main Breaker Status Monitor mode buttonsTo Work in Offline Mode 5.5 Using the Configuration Tool5.5.1 Starting the Configuration Program To Connect via COM Port5.5.2 Main Configuration Window Overview Overview of main Configuration window5.5.4 Install Configuration Changes in the Unit 5.5.3 Load a Configuration File from Disk5.5.5 Save the Configuration File to Disk 5.5.6 Select Panel to View 5.5.7 Select Breakers to View5.5.9 Edit the Panel Properties or Set a Password 5.5.8 Edit the Liebert LDM Unit PropertiesThe number of poles selected when the breaker was 5.5.10 Edit the Breaker Propertiesbreaker has tripped or the equipment has shut down If NOT assigned, a breaker position is shown with a Liebert logo 5.5.11 Add or Delete a Circuit Breaker5.5.12 Adding a Circuit Breaker Add Breaker Assigned breaker positions Unassigned breaker positionsAuxiliary Breaker View 5.5.13 Adding a Subfeed BreakerPanel Breaker View Add Subfeed Assigned breaker positions Unassigned breaker positions5.5.14 Delete a Breaker 5.6 Upgrading the Firmware The correct COM Port is selected and the Baud Rate is 10. Wait for the firmware upgrade to complete 6.0 SPECIFICATIONS Specifications7.0 TROUBLESHOOTING / FAQS Page Ne t Ensuring The High Availability0f Mission-Critical Data And Applications ti n