Unit Handling, Unpacking the Unit Domestic Packaging | Liebert XDV

General product information

3.3.2Unit Handling

If possible, transport the unit using a forklift or pallet jack.

•If using a forklift or pallet jack, ensure that the fork tine length is suitable to safely move the packaged unit.

•Liebert Corporation recommends that the unit remain in the protective packaging until located at the installation site.

•When handling and unpacking the unit, exercise great care to prevent damage.

•Do not use unit piping to lift or move the Liebert XDV

3.3.3Unpacking the Unit Domestic Packaging

1.Remove outer packaging when ready to install the Liebert XDV.

2.Keep the Liebert XDV covered by the unit bag until removal from pallet.

Figure 5 Removing domestic shipping package

Plastic bag used for shipping not shown for clarity.

Step 1

Step 2

Step 3

Do not use unit piping to lift or move the Liebert XDV

Step 4

Step 5

5

Image 11

Liebert XDV manual Unit Handling, Unpacking the Unit Domestic Packaging

Contents

Liebert XDV Fluorinated Greenhouse Gas Requirements-European Union General Safety Guidelines Table of Contents Electrical Installation Checklist and System Fill for StartupMaintenance Specifications Figures Page Liebert XDV component locations Example XDV10BK References Pre-Installation ChecksInstallation Considerations Installation General Product Information Product/System DescriptionChecking and Unpacking Recyclable Packaging Equipment Inspection Unpacking the Unit Domestic Packaging Unit Handling Removing export shipping package Export Packaging Removing Liebert XDV from shipping pallet Removing the Liebert XDV from the Pallet Mechanical Considerations Determining Placement in the Conditioned SpaceDimensional data Changing the Liebert XDV’s air intake location Changing the Air Intake Location Bolting Liebert XDV to Top of Cabinet Mounting the Liebert XDV on Top of the CabinetMounting the Liebert XDV Bottom View Mounting clip placement Using Supplied Clips for Mounting Pg , Rev Suspension hardware and bracket dimensional dataSuspended Mounting Method 11mm 22mm Top View 2 64mm 76mm 102mm DPN000770 Suspending the Liebert XDV from Overhead Structures Suspending the Liebert XDV from Unistruts Suspending Liebert XDV from the overhead structure Stacking configuration offset Mounting Liebert XDVs in Stacked Setup Stacked Liebert XDVs suspended from Unistruts Hanging Stacked Liebert XDVs from Unistruts Hanging Stacked Liebert XDVs from the Overhead Structure Piping System Connection ConfigurationEuropean Union Fluorinated Greenhouse Gas Requirements Piping Connections to Liebert XDP or Liebert XDC Connection Methods and Points Right Side Liebert XDV Holding Charge-Hard-Piped Units Hard Piped Connection Sizes Brazing Preparations-Hard-Piped Units Recommended Piping Size Branch piping sizes for refrigerant loop Connection Methods-One-Shot Connections Refrigerant Charge-Pre-Charged Option Field Installation of Liebert Flex Pipe Kit on Liebert XDVConnecting Liebert XD Flex Pipe to Liebert XDV Modules Tools Required Liebert XD prefabricated piping assembly Overtighten With wrench Return Piping mains without Liebert XDV and Liebert Flex Pipe Insulation Rear of Liebert XDV Connecting High Voltage Cables for CSA/C-US Certified UnitsElectrical Rear Liebert XDV Liebert XDV electrical connections for CE-approved units Rear View of Liebert Xdvto be N.E.C. Class Connecting Low Voltage Wiring-OptionalCondensate Detection Connections Installation Checklist and System Fill for Startup Checklist for Proper Installation Operation Start the Liebert XDV Fluorinated Greenhouse Gas Requirements Internal AccessMaintenance Accessing internal electrical components Accessing Internal Electrical Components To remove the fan tray Liebert XDV10 specifications Specifications Liebert XDV8 specifications Liebert XD Liebert Flex Pipe assemblies, supply and return Page That Ne tIti Ti n