PC Board Troubleshooting Procedures

TROUBLESHOOTING & REPAIR

Return to Section

Return to Section TOC

Return to Master

Return to Master TOC

WARNING

ELECTRIC SHOCK can kill.

Have an electrician install and service this equipment. Turn the input power OFF at the fuse box before working on equipment. Do not touch electrically hot parts.

CAUTION: Sometimes machine failures appear to be due to PC board failures. These problems can some- times be traced to poor electrical connections. To avoid problems when troubleshooting and replacing PC boards, please use the following procedure:

1.Determine to the best of your technical ability that the PC board is the most likely component causing the failure symptom.

2.Check for loose connections at the PC board to assure that the PC board is properly connected.

3.If the problem persists, replace the suspect PC board using standard practices to avoid static elec- trical damage and electrical shock. Read the warn- ing inside the static resistant bag and perform the following procedures:

PC Board can be damaged by static electricity.

•Remove the PC Board from the static-shielding bag and place it directly into the equipment. Don’t set the PC Board on or near paper, plastic or cloth which could have a static charge. If the PC Board can’t be installed immediately, put it back in the static-shielding bag.

•If the PC Board uses protective shorting jumpers, don’t remove them until installation is complete.

•If you return a PC Board to The Lincoln Electric Company for credit, it must be in the static-shielding bag. This will prevent further damage and allow prop- er failure analysis.

4.Test the machine to determine if the failure symp- tom has been corrected by the replacement PC board.

NOTE: It is desirable to have a spare (known good) PC board available for PC board troubleshooting.

NOTE: Allow the machine to heat up so that all electri- cal components can reach their operating temperature.

5. Remove the replacement PC board and substitute

it with the original PC board to recreate the original

problem.

a. If the original problem does not reappear

Return to Section TOC

Return to Master TOC

ATTENTION Static-Sensitive Devices Handle only at Static-Safe Workstations

Reusable

Container

Do Not Destroy

•Remove your body’s static charge before opening the static-shield- ing bag. Wear an anti-static wrist strap. For safety, use a 1 Meg ohm resistive cord connected to a grounded part of the equipment frame.

•If you don’t have a wrist strap, touch an unpainted, grounded, part of the equipment frame. Keep touching the frame to pre- vent static build-up. Be sure not to touch any electrically live parts at the same time.

•Tools which come in contact with the PC Board must be either con- ductive, anti-static or static-dissi- pative.

by substituting the original board, then the

PC board was not the problem. Continue

to look for bad connections in the control

wiring harness, junction blocks, and termi-

nal strips.

b. If the original problem is recreated by the

substitution of the original board, then the

PC board was the problem. Reinstall the

replacement PC board and test the

machine.

6. Always indicate that this procedure was followed

when warranty reports are to be submitted.

NOTE: Following this procedure and writing on the warranty report, “INSTALLED AND SWITCHED PC BOARDS TO VERIFY PROBLEM,” will help avoid denial of legitimate PC board warranty claims.

SQUARE WAVE TIG 275

SVM141-A specifications

The Lincoln Electric SVM141-A is a cutting-edge solution designed for operators requiring precision, efficiency, and versatility in their welding applications. This machine is known for its compact form but robust feature set, making it an ideal choice for both professional welders and industrial applications.

One of the standout features of the SVM141-A is its advanced inverter technology. This innovation allows for a stable arc, providing consistent results even under varying conditions. The machine minimizes power consumption, making it energy-efficient without compromising performance. The inverter technology also supports a wider input voltage range, making the SVM141-A suitable for use in diverse environments and job sites.

Another key characteristic is its multi-process capability. The SVM141-A supports MIG, stick, and TIG welding processes, providing flexibility for various welding tasks. This versatility enables operators to tackle different materials, including mild steel, stainless steel, and aluminum, making it a valuable tool for numerous projects.

The user-friendly interface of the SVM141-A includes an intuitive digital display, which allows welders to adjust settings with ease. This feature is crucial for ensuring the right configurations for specific welding tasks, reducing the chances of errors and enhancing the overall finish of welds.

Safety is also a priority with the Lincoln Electric SVM141-A. It comes with built-in safety features such as overheat protection and automatic shutdown, ensuring operator safety and equipment longevity. The machine's lightweight design enhances portability, allowing it to be used in various workspaces with ease.

Durability is another hallmark of the SVM141-A. Constructed with high-quality materials, the machine is designed to withstand the rigors of demanding work environments. This ensures reliability over time, providing consistent performance even under heavy use.

In summary, the Lincoln Electric SVM141-A is a versatile, efficient, and user-friendly welding machine that appeals to a wide range of users. Its advanced inverter technology, multi-process capabilities, safety features, and durable construction make it a strong contender in the welding market, suitable for both professionals and hobbyists alike. Whether it’s for light fabrication, repairs, or industrial welding tasks, the SVM141-A meets diverse needs with precision and reliability.

Lincoln Electric SVM141-A service manual PC Board Troubleshooting Procedures

Models: SVM141-A

TOC

TROUBLESHOOTING & REPAIR