TOC

F-3

TROUBLESHOOTING AND REPAIR

F-3

 

PC BOARD TROUBLESHOOTING PROCEDURES

 

Return to Section

Return to Section TOC

Return to Master

Return to Master TOC

WARNING

ELECTRIC SHOCK can kill.

Have an electrician install and service this equipment. Turn the input power OFF at the fuse box before working on equipment. Do not touch electrically hot parts.

CAUTION

Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor electrical connections. To avoid prob- lems when troubleshooting and replacing PC boards, please use the following procedure:

1.Determine to the best of your technical ability that the PC board is the most likely component causing the failure symptom.

2.Check for loose connections at the PC board to assure that the PC board is properly connected.

3.If the problem persists, replace the suspect PC board using standard practices to avoid static electrical damage and electrical shock. Read the warning inside the static resistant bag and perform the following procedures:

-Remove the PC board from the static-shielding bag and place it directly into the equipment. Don’t set the PC board on or near paper, plastic or cloth which could have a static charge. If the PC board can’t be installed immediately, put it back in the static-shield- ing bag.

-If the PC board uses protective shorting jumpers, don’t remove them until installation is complete.

-If you return a PC board to The Lincoln Electric Company for credit, it must be in the static-shielding bag. This will prevent further damage and allow prop- er failure analysis.

4.Test the machine to determine if the failure symptom has been corrected by the replacement PC board.

NOTE: It is desirable to have a spare (known good) PC board available for PC board troubleshooting.

NOTE: Allow the machine to heat up so that all electrical components can reach their operating temperature.

5.Remove the replacement PC board and substitute it with the original PC board to recreate the original problem.

a.If the original problem does not reappear by substituting the original board, then the PC board was not the problem. Continue to look for bad connections in the control wiring harness, junction blocks, and terminal strips.

TOC

PC board can be damaged by static electricity.

b. If the original problem is recreated by the

Return to Section

Return to Master

ATTENTION

Static-Sensitive

Devices

Handle only at

Static-Safe

Workstations

-Remove your body’s static charge before opening the static- shielding bag. Wear an anti-static wrist strap. For safety, use a 1 Meg ohm resistive cord connected to a grounded part of the equipment frame.

-If you don’t have a wrist strap, touch an un-painted, grounded, part of the equipment frame. Keep touching the frame to prevent static build-up. Be sure not to touch any electrically live parts at the same time.

substitution of the original board, then the PC board was the problem. Reinstall the replacement PC board and test the machine.

6.Always indicate that this procedure was followed when warranty reports are to be submitted.

NOTE: Following this procedure and writing on the warranty report, “INSTALLED AND SWITCHED PC BOARDS TO VERIFY PROBLEM,” will help avoid denial of legitimate PC board warranty claims.

Return to Section TOC

Return to Master TOC

-Tools which come in contact with the PC board must be either conductive, anti-static or static-dissipative.

SAE-400 SEVERE DUTY

Page 43
Image 43
Lincoln Electric SVM187-A service manual Troubleshooting and Repair, PC Board Troubleshooting Procedures

SVM187-A specifications

The Lincoln Electric SVM187-A is a cutting-edge welding machine designed for professional welders and industrial applications. Known for its reliability and performance, it stands out in the competitive welding equipment market. This versatile machine is structured to handle various welding processes, making it a popular choice among users.

One of the primary features of the SVM187-A is its multifunctional capabilities. It supports MIG, TIG, and Stick welding, allowing users to switch between different welding techniques seamlessly. This flexibility makes it suitable for diverse applications, whether working on automotive repairs, metal fabrication, or construction projects. Additionally, the machine is equipped with a robust power output, ranging from low to high amperage settings, enabling users to tackle a wide array of materials, including mild steel, stainless steel, and aluminum.

The SVM187-A incorporates advanced inverter technology, which ensures increased efficiency and reduced energy consumption. This technology leads to a more compact design, making the unit portable and easy to transport. The lightweight construction of the machine does not compromise its durability; it is built with high-quality materials to withstand the rigors of a professional workshop.

Another notable characteristic of the SVM187-A is its user-friendly interface. The intuitive control panel includes digital displays for precise settings adjustments, ensuring accuracy during operation. Beginners and seasoned welders alike can benefit from the clear and straightforward design, reducing training time and enhancing productivity.

Safety features are paramount in the SVM187-A's design. The machine is equipped with thermal overload protection, ensuring that it operates within a safe temperature range to prevent damage and promote longevity. Additionally, it features automatic voltage regulation, which maintains a stable arc even under varying input voltage conditions.

In summary, the Lincoln Electric SVM187-A is a versatile, efficient, and user-friendly welding machine suited for both professional and industrial applications. Its multifunctionality, inverter technology, and robust safety features set it apart from competitors, making it a reliable choice for welders seeking to elevate their craftsmanship while ensuring safety and efficiency. This machine represents the innovation and quality that Lincoln Electric is renowned for in the welding industry.