Industry Canada Statement | Linksys SFE2010P specification

D

Federal Communication

Commission Interference

Statement

This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

The Class [A] digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numerique de la class [A] respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

EC Declaration of Conformity (Europe)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards:

•EN55022 Emission

•EN55024 Immunity

SFE2010/SFE2010P Administration Guide

59

Image 62

Linksys SFE2010P manual Industry Canada Statement, EC Declaration of Conformity Europe

Contents

Port 10/100 Ethernet Switch Table of Contents Contacts Welcome What’s in this User Guide? Getting to Know the SFE2010/SFE2010P SFE2010/P Front Panel Getting to Know the SFE2010/SFE2010P SFE2010/P Back Panel Sample Network Configuration Maximum Cabling Distances Desktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Connecting the Cables Wall-Mount Placement Connecting Devices Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based Utility Viewing On-line Help Using the Console Connecting to Your Switch with HyperTerminal Using the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console Using the Switch Main Menu System Configuration To open this menu System InformationTo open this screen Versions General Information Management Settings To change the system contact, system name, and location To change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration SSH Configuration To change the time-out setting SSH Server Configuration To change SSH Server settings To change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto key Security Settings To change User & Password settings SSL Generate Certificate To edit and execute a certificate Show Certificate Disable Active Management Access ProfileTo disable the active management access profile Default Vlan Setup Vlan Management IP Configuration To edit the Vlan ID IPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settings To change the Http settings Http ConfigurationHttps Configuration To open the screen Network Configuration To change Https settings To change the IP address To begin the ping test Ping IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File Management To enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified location To enter the active image settings Active Image Reboot System Restore System Default SettingsReset to Factory Settings To restore system default settings Stack Configuration Port Status Port Status PoE Status Port Configuration Port Settings PoE Settings To configure the ports System Mode Layer 2 / Layer 3 Selection To configure the PoE settings To edit the system mode or stacking mode Help Logout US/Canada Contacts EU Contacts Customer Site Survey Yes Limited Warranty Exclusions and Limitations Obtaining Warranty Service Technical Support Obtaining Warranty Service Industry Canada Statement EC Declaration of Conformity Europe Specifications Radius Vlan EMC 080312A-LB