Connecting Devices | Linksys SFE2010P specification

Connecting Devices

Connecting the Cables

CAUTION: Observe the orientation of the mini-GBIC module before inserting it into a mini- GBIC port. The bottom mini-GBIC ports are upside down in relation to the top mini-GBIC ports.

5.If you use the console interface to configure the Ethernet switch, then connect the supplied serial cable to the console port (located on the back of the Ethernet switch), and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (The PC must be running VT100 terminal emulation software, such as HyperTerminal.)

6.Connect the supplied power cord to the power port, and plug the other end into an electrical outlet.

CAUTION: Make sure you use the power cord that is supplied with the Ethernet switch. Use of a different power cord could damage the Ethernet switch.

7.Power on the network devices connected to the Ethernet switch. Each active port’s corresponding Act/Link LED will light up on the Ethernet switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

8.Proceed as needed:

•If you will use the console interface to configure the Ethernet switch, proceed to ”Console Configuration” section on page 33 for directions.

•If you use the Web-based Utility to configure the Ethernet switch, proceed to ”Web Utility Configuration” section on page 50.

SFE2010/SFE2010P Administration Guide

9

Image 12

Linksys SFE2010P manual Connecting Devices

Contents

Port 10/100 Ethernet Switch Table of Contents Contacts Welcome What’s in this User Guide? Getting to Know the SFE2010/SFE2010P SFE2010/P Front Panel Getting to Know the SFE2010/SFE2010P SFE2010/P Back Panel Sample Network Configuration Maximum Cabling Distances Before You Install the Switch Placement OptionsDesktop Placement Rack-Mount Placement Connecting the Cables Wall-Mount Placement Connecting Devices Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based Utility Viewing On-line Help Using the Console Connecting to Your Switch with HyperTerminal Using the Console Set the serial port settings as follows Connecting to the Switch with Telnet Logging On to the ConsoleSelecting Menu Options and Actions Using the Switch Main Menu System Configuration System Information To open this screenTo open this menu Versions General Information Management Settings To change the system contact, system name, and location Serial Port Configuration Telnet ConfigurationTo change the baud rate of the serial port SSH Configuration To change the time-out setting SSH Server Configuration To change SSH Server settings To change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto key Security Settings To change User & Password settings SSL Generate Certificate To edit and execute a certificate Disable Active Management Access Profile To disable the active management access profileShow Certificate Default Vlan Setup Vlan Management IP Configuration To edit the Vlan ID IPv4 Address Configuration IPv6 Address Configuration To edit the IPv4 address settingsTo renew Dhcp To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settings Http Configuration Https ConfigurationTo change the Http settings To open the screen Network Configuration To change Https settings To change the IP address To begin the ping test Ping IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File Management Upgrade / Backup IPv6 To enter the IPv4 Upgrade/Backup file name and locationTo enter the IPv6 Upgrade/Backup file name and location To download a file from the specified location To enter the active image settings Active Image Restore System Default Settings Reset to Factory SettingsReboot System To restore system default settings Stack Configuration Port Status Port Status PoE Status Port Configuration Port Settings PoE Settings To configure the ports System Mode Layer 2 / Layer 3 Selection To configure the PoE settings To edit the system mode or stacking mode Help Logout US/Canada Contacts EU Contacts Customer Site Survey Yes Limited Warranty Exclusions and Limitations Obtaining Warranty Service Technical Support Obtaining Warranty Service Industry Canada Statement EC Declaration of Conformity Europe Specifications Radius Vlan EMC 080312A-LB