Manuals / Locke / Kitchen Appliance / Kitchen Utensil

Locke RS-5100 Refer to -6 and, Micro Switch Turned to the Left, Micro Switch Turned to the Right

Models: RS-5100

1 32

Download 32 pages 39.58 Kb

Page 16

Refer to Figure 3-6 and 3-7:

6.Manually move grinding carriage left and right making sure there is ample clearance between the stone and the end of the reel blades. (It may be necessary to reposition the reel unit slightly.) When satisfied that the grinding wheel clears the reel unit at both ends, tighten the brackets. Figure 3-5.

There are two ways to make reel adjustments:

A.The grinder’s movable base is used if the bed- knife is adjusted to the reel.

B.The reel unit’s own adjusters may be used if the reel to bedknife adjustment is made by moving the reel to the knife.

Refer to Figure 3-6 and 3-7:

Manually turn traverse micro switch arm (the white ny- lon rod) to the left. Move reel grinding carriage to the left of the reel unit making sure the grinding wheel clears the end of the reel blades. Keeping the carriage in this position slide the limit stop to the right until the actuating screw throws the traverse micro switch arm to the right. Tighten the handle on the center limit stop. Set the right limit stop in the opposite manner.

14

Micro Switch Turned to the Left

Figure 3-6

Micro Switch Turned to the Right

Figure 3-7

Image 16

Locke RS-5100 manual Refer to -6 and, Micro Switch Turned to the Left, Micro Switch Turned to the Right

Contents

Page Page Page Page REEL and BEDKNIFE SHARPENER DEALER PREPARATION CHECK LISTIntroduction Getting Acquainted With Your Reel and Bedknife SharpenerOwner Assistance Serial NumberSECTION 1 - SAFETY Important Safety InformationSafety Notations Safety RulesSafety Decals MaintenancePersonal Safety Equipment IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONSDUTIES OSHA RegulationsSECTION 2-ASSEMBLY INSTRUCTIONS AND SET-UP Uncrating the SharpenerLocating The Grinder Securing the SharpenerPage Electrical Wiring Source To Front Panel Models -220 Volts Wiring The 5100 Sharpener DANGERTHIS SHOULD BE DONE BY AN EXPERI ENCED, LICENSED ELECTRICIAN Electrical Wiring Source To Front Panel Models-240 volts Foreign CoolantChanging Wheel heads Spin Grinding Refer to Figure 3-2 andMicro Switch Turned to the Left Refer to Figure 3-6 andMicro Switch Turned to the Right Spin Motor Brackets Wobble ExtensionsShaft Being Reversed Figure 3-9 A Indexing The Ratchet Wheel RPM SettingRatchet Wheel Engaging TraverseManual Relief Grinding LeftRatchet Pawl Finger GuideThumb Bolt A B GuardGrinding Relief Angles on Reels Grinding the AnglesSharpening Bedknives Grinding Angle Adjustment Found with Angle Finder“L” Brackets Bedknife Secured with “L” Brackets9. Start the wheel head motor Bedknife Adjustment Handle Figure 3-26b Grinding Relief Angles on BedknivesBedknife/Reel Relief Angle Figure 3-26a Refer to Figure 3-29 and Grinding Angle AdjustmentClean-Up SECTION 4-MAINTENANCE & LUBRICATIONRefer to Figure 4-2 and DANGER Servicing the StonesDressing the Stone Belt TensionONLY QUALIFIED ELECTRICIANS SHOULD SERVICE THIS AREA OF THE GRINDER SECTION 5-TROUBLESHOOTINGDANGER Frequently Asked Questions SAFETY SHIELDS ARE INSTALLED FOR YOUR PROTECTION1. Why does the sharpener have safety shields? 2. Why does the sharpener have the water/coolant mix?SAFETY DECALS TURN OFF MAIN POWER AND LOCK OUT THE DISCONNECTSWITCH BEFORE OPENING THIS ELECTRICAL ENCLOSURE BASIC GRINDER SAFETY PRACTICES TO AVOID SERIOUS INJURY OR DEATHMETRIC AMERICANTORQUE SPECIFICATIONS 307 Highway 52E Opp, Alabama Locke Turf