Manuals / Locke / Kitchen Appliance / Kitchen Utensil

Locke RS-5100 manual Danger, Servicing the Stones, Dressing the Stone, Belt Tension

Models: RS-5100

1 32

Download 32 pages 39.58 Kb

Page 27

Image 27

3.Clean the water reservoir and screens after ap- proximately 60 to 70 units of work. To remove the water reservoir:

A.Disconnect the power supply.

B.Remove the rear cover from the machine.

C.Pull the drain hose out of the lid.

D.Slide the tank out.

Servicing the Stones

DANGER

EXTREME CARE MUST BE TAKEN TO AVOID CRACKING THE STONE. A CHIPPED OR BRO- KEN STONE COULD CAUSE SERIOUS INJURY TO THE OPERATOR.

Dressing the Stone

For true roundness, dressing with an optional diamond dressing tool works well. To remove glazing, open the pores and reshape the cupped stone. An optional granite dressing stick may be used.

Belt Tension

The tension of the toothed drive belt may be adjusted by loosening the hex nut and sliding the tensioner up or down in the slotted hole. After desired tension is achieved, retighten the hex nut. Figure 4-4

Page 27

Image 27

Locke RS-5100 manual Danger, Servicing the Stones, Dressing the Stone, Belt Tension

Contents

Page Page Page Page DEALER PREPARATION CHECK LIST REEL and BEDKNIFE SHARPENERSerial Number IntroductionGetting Acquainted With Your Reel and Bedknife Sharpener Owner AssistanceSafety Rules SECTION 1 - SAFETYImportant Safety Information Safety NotationsMaintenance Safety DecalsPersonal Safety Equipment OSHA Regulations IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS DUTIESSecuring the Sharpener SECTION 2-ASSEMBLY INSTRUCTIONS AND SET-UPUncrating the Sharpener Locating The GrinderPage Wiring The 5100 Sharpener DANGER Electrical Wiring Source To Front Panel Models -220 VoltsTHIS SHOULD BE DONE BY AN EXPERI ENCED, LICENSED ELECTRICIAN Coolant Electrical Wiring Source To Front Panel Models-240 volts ForeignChanging Wheel heads Refer to Figure 3-2 and Spin GrindingRefer to Figure 3-6 and Micro Switch Turned to the LeftMicro Switch Turned to the Right Wobble Extensions Spin Motor BracketsShaft Being Reversed Figure 3-9 A Engaging Traverse Indexing The Ratchet WheelRPM Setting Ratchet WheelFinger Guide Manual Relief GrindingLeft Ratchet PawlA B Guard Thumb BoltGrinding the Angles Grinding Relief Angles on ReelsBedknife Secured with “L” Brackets Sharpening BedknivesGrinding Angle Adjustment Found with Angle Finder “L” Brackets9. Start the wheel head motor Grinding Relief Angles on Bedknives Bedknife Adjustment Handle Figure 3-26bBedknife/Reel Relief Angle Figure 3-26a Grinding Angle Adjustment Refer to Figure 3-29 andSECTION 4-MAINTENANCE & LUBRICATION Clean-UpRefer to Figure 4-2 and Belt Tension DANGERServicing the Stones Dressing the StoneSECTION 5-TROUBLESHOOTING ONLY QUALIFIED ELECTRICIANS SHOULD SERVICE THIS AREA OF THE GRINDERDANGER 2. Why does the sharpener have the water/coolant mix? Frequently Asked QuestionsSAFETY SHIELDS ARE INSTALLED FOR YOUR PROTECTION 1. Why does the sharpener have safety shields?BASIC GRINDER SAFETY PRACTICES TO AVOID SERIOUS INJURY OR DEATH SAFETY DECALSTURN OFF MAIN POWER AND LOCK OUT THE DISCONNECT SWITCH BEFORE OPENING THIS ELECTRICAL ENCLOSUREAMERICAN METRICTORQUE SPECIFICATIONS Locke Turf 307 Highway 52E Opp, Alabama