Resharpening the Cutting Tool, Stopping | Makita EM2650UH, EM2650LH

STOPPING

1)Release the throttle lever (2) fully, and when the engine rpm has lowered, set the I-O switch to STOP the engine will now stop.

2)Be aware that the cutting head may not stop immediately and allow it to slow down fully.

	STOP	(1)
	STOP
	(2)
STOP
(2)
(1)
EM2650LH		EM2650UH

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.

CHECKUP OF LOW-SPEED ROTATION

–Set the low-speed rotation to 3,000 min-1.

If it is necessary to change the low speed rotation (idle) speed, use a phillips head screw driver on the screw illustrated on the right.

–Turn the adjusting screw to the right, and the engine rotation will increase. Turn the adjusting screw to the left, and the engine rotation will drop.

–The carburetor is generally adjusted before shipment. After several tanks of gasoline the idle rpm may need to be readjusted.

Carburetor

Adjusting

screw

RESHARPENING THE CUTTING TOOL

CAUTION: The cutting tools shown in the illustration are not to be sharpened. Manual resharpening will result in imbalances of the cutting tool causing vibrations and damage to the equipment.

NOTE: To increase the service life of the cutter blade it may be turned over once, until both cutting edges have become blunt.

NYLON CUTTING HEAD

The grass trimmer cutting head is a dual line trimmer head that has bump & feed mechanism.

The nylon cutting head will feed out the proper length of nylon line after tapping the trimmer head on the ground by changes in centrifugal force caused by increasing or decreasing rpms.

Operation

–Increase the nylon cutting head speed to approx. 6,000 min-1. Bump the trimmer head lightly on the ground.

–The most effective cutting area is shown by the shaded area.

–If the nylon cord does not feed out, rewind/replace the nylon cord by following the procedures described under “Replacing the nylon cord.”

Most effective cutting area

17

Image 17

Makita EM2650UH manual Resharpening the Cutting Tool, Stopping, Adjustment of LOW-SPEED Rotation Idling, Nylon Cutting Head

Contents

Importante EM2650UH EM2650LH Table of Contents Symbols General Instructions Safety InstructionsIntended use of the machine Personal protective equipment Refueling Resting Transport Refueling Maintenance Tool replacement Method of operation Maintenance instructionsCutting Tools Kickback First Aid When asking for help, please give the following informationNever straighten or weld damaged cutting tools Model EM2650UH EM2650LH Technical Data EM2650UH, EM2650LH EM2650UH Designation of Parts For machines with loop handle Mounting of HandleFor machines with bike handle models Use of nylon cutting head EM2650UH, EM2650LH Use of metal blade EM2650UH, optional accessory for EM2650LH For EM2650LH Mounting of ProtectorFor EM2650UH Mounting of nylon cutting head Mounting of Cutter Blade or Nylon Cutting HeadMounting of cutterblade with the hex wrench still in place Oil volume Point 1 in Replacement of oil Oil capBefore Start of Operation Inspection and reﬁll of engine oil Handling of fuel RefuelingStorage period of fuel Fuel Starting Points in Operation and HOW to StopCorrect Handling of Machine Startup after warm-up operation At times, such as winter, when starting the engine Resharpening the Cutting Tool Adjustment of LOW-SPEED Rotation IdlingStopping Checkup of LOW-SPEED Rotation Replacing the nylon cord Servicing Instructions Daily checkup and maintenanceReplacement of Engine OIL Points on OIL Cleaning of AIR CleanerPoints in Handling Air Cleaner Element Replacement of Fuel Pipe Cleaning of Fuel FilterCleaning of Parts Replacement of Gaskets and Packings Storage Fault locationFault System Observation Cause Daily 50h Shutdown Operating time BeforeOperation 30h 200h State of abnormality Probable cause malfunction Remedy TroubleshootingStarts. Once engine starts, cutter blade Blade Emission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Parts Covered Emission Component Defect Warranty Period OWNER’S Warranty Responsibilities Obtaining Warranty ServiceWhat is not Covered HOW to Make a Claim Table des matières Pictogrammes Consignes générales Consignes DE SécuritéUtilisation normale de la machine Équipement de protection personnel Remplissage Pause Transport Remplissage Entretien Remplacement d’outil Outils de coupe Mode de fonctionnementMouvement de recul Prévention des mouvements de recul Premiers soins Modèle EM2650UH EM2650LH Données Techniques EM2650UH, EM2650LH Désignation DES Pièces Désignation DES Pièces Pour les machines avec poignée arceau Montage DE LA PoignéePour les machines avec guidon Poignée Sangle Utilisation d’une tête à ﬁls nylon EM2650UH, EM2650LH Pour le EM2650LH Montage DU ProtecteurPour le EM2650UH Montage de la tête à ﬁls nylon Montage DE LA Lame DE Coupe OU DE LA Tête À Fils NylonMakita Quantité d’huile Environ 0,08 l Avant UtilisationInspection et remplissage de l’huile moteur Manipulation de l’essence RemplissageEntreposage de l’essence Carburant Fixation de la sangle d’épaule Manipulation Correcte DE LA MachineDétachement Démarrage Pendant les périodes, telles que l’hiver, où Démarrage après le réchauffage Arrêt Réaffûtage DE L’OUTIL DE CoupeRéglage DE LA Rotation À Faible Vitesse Ralenti Vérification DE LA Rotation À Faible Vitesse Remplacement du ﬁl nylon Huile recommandée Remplacement DE L’HUILE MoteurInstructions D’ENTRETIEN Vériﬁcation et entretien quotidiens Nettoyage DU Filtre À AIR Remarques Concernant L’HUILE Remplacement DES Joints ET Garnitures Remplacement DU Tuyau D’ALIMENTATION EN EssenceVérification DE LA Bougie D’ALLUMAGE Lubrification DU Carter D’ENGRENAGE Défaillance Système Observation Cause Emplacement des défaillancesEntreposage Arrêt Quotidien Fonctionnement30 h 50 h 200 h Pause Dépannage Anomalie Cause probable dysfonctionnement SolutionFois le moteur démarré, la rotation de la Lame de coupe commence. Faites très ÍndicePágina Símbolos Instrucciones generales Instrucciones DE SeguridadUso intencionado de la herramienta Equipo protector personal Resuministro de combustible Piezas cortadoras Método de operaciónRetrocesos bruscos Prevención de retrocesos bruscos Primeros auxilios Modelo EM2650UH EM2650LH Especificaciones Técnicas EM2650UH, EM2650LH Identificación DE LAS Piezas Identificación DE LAS Piezas Para modelos equipados con mango tipo redondo Colocación DEL MangoPara modelos equipados con mango tipo bicicleta Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Para EM2650LH Colocación DEL ProtectorPara EM2650UH Colocación de la cabeza cortadora de nailon Colocación DEL Disco Cortador O Cabeza Cortadora DE Nailon Antes DE Iniciar LA Operación Volumen de aceite Aprox ,08LInspeccione y resuministre el aceite del motor Punto 1 en el reemplazo del aceite Tapa del aceite Manejo del combustible Reabastecimiento DE CombustiblePeriodo de almacenamiento del combustible Combustible Arranque DEL Motor Manejo Correcto DEL EquipoPuntos EN LA Operación Y Cómo Detener LA Operación En ciertas ocasiones, como en el invierno, cuando Arranque tras la operación de calentamiento Paro DE LA Operación Reafilado DE LA Pieza CortadoraAjuste DE LA Rotación DE Baja Velocidad Estado Pasivo Revisión DE LA Rotación DE Baja Velocidad Reemplazo del cordón de nailon Reemplazo DEL Aceite DEL Motor Instrucciones DE ServicioRevisión y mantenimiento diarios Puntos en el manejo del elemento del ﬁltro de aire Puntos Sobre EL AceiteLimpieza DEL Filtro DE Aire Revisión DE LA Bujía DE Encendido Engrasado DE LA Caja DE CambiosInspección DE PERNOS, Tuercas Y Tornillos Limpieza DE LAS Piezas Atención AlmacenamientoAtención tras el almacenamiento de largo plazo Determinación de fallas Acción Antes Tras la DiarioOperación 30h 50h 200h Cortador Resolución DE ProblemasEstado de anomalía Causa probable falla Solución Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Intervalo Procedimiento Piezas Cubiertas Periodo DE Garantía POR Defectos DE Componentes DE Emisiones Responsabilidades DEL Propietario Para LA Garantía Obtención DE Servicio DE GarantíaLO QUE no Está Cubierto Cómo Preparar UNA Reclamación Page Advertencia