ENGLISH
SCANNING THE CODE TABLE | RESETTING THE ALL CODE |
|
|
|
|
|
| OSD |
| MENU |
|
|
|
|
|
| OSD |
| MENU | ||
| POWER |
|
|
|
|
| OK |
|
| POWER |
|
|
|
|
| OK |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| TV | VCR1 | DSS/VCR2 | DVD | 2. | SETUP/ | MENU OFF |
|
| TV | VCR1 | DSS/VCR2 | DVD | 1. | SETUP/ | MENU OFF |
| ||
| T.TONE |
|
|
| T.TONE |
|
| ||||||||||||
|
|
|
|
| AUTO |
| DTS |
|
|
|
|
| AUTO |
| DTS | ||||
| TUNER | CD | TAPE | CDR/MD | 6. |
| 4 | 5 | 6 |
|
|
|
|
|
| 4 | 5 | 6 | |
|
|
| 1 | 2 | 3 |
| TUNER | CD | TAPE | CDR/MD |
| 1 | 2 | 3 | |||||
|
|
|
|
|
| NIGHT | CSII | EX/ES | DSP |
| NIGHT | CSII | EX/ES | DSP | |||||
|
| AUX | AMP |
|
| DISPLAY | STEREO | 6.1CH IN |
|
| AUX | AMP |
|
| DISPLAY | STEREO | 6.1CH IN | ||
|
|
| 3. |
| 7 | 8 | 9 |
|
|
|
|
| 7 | 8 | 9 | ||||
2. |
|
|
|
|
|
|
|
|
|
| 2. |
| |||||||
TV |
|
| MAIN | CLEAR | MEMO | A/D | P.SCAN | 1. | TV |
|
| MAIN | CLEAR | MEMO | A/D | P.SCAN | |||
VOL. | SLEEP | MUTE | VOL. |
|
| 0 |
| VOL. | SLEEP | MUTE | VOL. |
|
| 0 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
| CHANNEL/SKIP |
|
|
|
|
|
| CHANNEL/SKIP | ||||||
| OSD |
| MENU |
| BASS | TREBLE | TUNE/SEARCH |
| OSD |
| MENU |
| BASS | TREBLE | TUNE/SEARCH | ||||
OPERATION OF REMOTE CONTROL | 3. Close until it clicks. |
UNIT |
|
REMOTE CONTROL |
|
The distance between the transmitter of the |
|
remote control unit and the IR SENSOR of the |
|
SR4400 should be less than about 5 meters. If the |
|
transmitter is pointed to a direction other than the |
|
IR SENSOR or if there is an obstacle between |
|
them, remote control may not be possible. |
|
1. Switch on the appliance which should be controlled.
2. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice.
3. Press the code 9 - 9 - 1. The indicator will blink twice.
4. Aim the remote control at the appliance and slowly alternate between pressing POWER and the function button for the appliance.
5. Stop when the appliance turns off.
6. Press SETUP once to lock in the code.
CHECKING THE CODE |
|
|
|
|
| |||
|
|
|
| 1. |
| OK |
| |
POWER |
|
|
|
|
|
|
| |
|
|
|
| SETUP/ | MENU OFF | |||
|
|
|
| 3. | T.TONE |
|
| |
|
|
|
| AUTO |
| DTS | ||
TV | VCR1 | DSS/VCR2 | DVD |
| 1 | 2 | 3 | |
|
|
|
| NIGHT | CSII | EX/ES | DSP | |
|
|
|
| 4. |
| 7 | 8 | 9 |
|
|
|
|
|
| 4 | 5 | 6 |
TUNER | CD | TAPE | CDR/MD |
| DISPLAY | STEREO | 6.1CH IN | |
|
|
|
|
| ||||
|
|
|
|
| CLEAR | MEMO | A/D | P.SCAN |
| AUX | AMP |
| 2. |
|
| 0 |
|
TV |
|
| MAIN |
|
| CHANNEL/SKIP | ||
|
|
|
|
|
| |||
VOL. | SLEEP | MUTE | VOL. |
|
|
|
| |
|
|
|
| BASS | TREBLE | TUNE/SEARCH | ||
OSD |
| MENU |
|
| MODE | DISP./RDS | F.DIRECT | |
1. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice.
2. Press the code 9 - 9 - 0. The indicator will blink twice.
3. To view the code for first digit, press 1 once. Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number.
Note:
1. Press and hold down the any function button and press SETUP until the indicator blinking twice.
2. Press the code 9 - 8 - 1. The indicator will blink twice.
Then, RC5400SR will return to the factory preset code.
Note:
After this procedure, the selected function button is set initial code and other function buttons are set initial code too.
Once you have found and the codes for your various appliances, you may want to write them down here.
TV
VCR
DSS
DVD
CD
TAPE
CDR
MD
SR4400 |
60°
Remote control unit (RC5400SR)
LOADING BATTERIES
The life of the batteries used with the remote control unit is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak.
1. Remove the back cover.
2. Insert the new batteries (AAA type) with
correct 
and 
polarity.
If a code digit is “0”, the indicator will not blink.
4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.
8
