Marantz SR4400 manual Programming The Remote, Controller, English, Numeric buttons

.Numeric buttons 1 to 9 (A, B, C ... Z, –) / Surround mode buttons

Numeric buttons

These buttons are used to enter figures in the selec- tion of a tuner preset station and station name pre- set or to set select a CD track number, etc. The func- tions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

These buttons are used to select the surround mode.

Note:

•The surround mode is set to 6-Stereo mode by pressing M-CH ST button.

⁄0P.SCAN (preset scan) button (when TUNER

mode is selected)

This button is used to start preset scan when SR4400 is selected TUNER mode.

⁄10 / A/D button

0 button

This button is used to enter the number “0”

A/D button (when AMP mode is selected)

This is used to switch between the analog and digital inputs.

⁄2CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc.

The function of these buttons are dependent on the function button selected.

For the controllable functions of each input function, please refer to contrable function table on the page 9.

⁄3ATT (attenuator) button

When the input signal is too high and the voice dis- torts even by throttling the SR4400 VOLUME con- trol, turn on this function. “ATT” is indicated when this function is activated.

The input level is reduced. Attenuator is invalid for use with the output signal of “REC OUT”.

Note:

•This function is unavailable during the digital input is selected.

⁄4TREBLE UP ( ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of high frequency sound for left and right speaker.

⁄5BASS UP ( ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

⁄6MEMO button

Memory enable button for various preset functions.

⁄7CLEAR button

This button is used to cancel for certain memory or programming operations.

⁄8DISPLAY button

When this button is pressed once, the display is dimmed.

When this button is pressed twice, the display is turned off and the “DISPLAY OFF” indicator lights up.

Press this button again to turn on the display again.

⁄9NIGHT button

Pressing this button prevents the Dolby Digital sig- nal from playback at a loud voice. This function re- duces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back.

When this button is pressed, “NIGHT” indicator lights up.

¤0S- ( Source) DIRECT button

When this button is pressed, the tone control circuit is bypassed as well as Bass Management.

¤1SETUP / T.TONE button

Test tone function is used for adjusting the balance between the volume levels of speaker channels. Press AMP button and press this button to enter the test tone mode.

¤2OSD button

Note:

• This button is unavailable for SR4400.

¤3SLEEP (sleep timer) button

This button is used for setting the sleep timer. It

can be operated the same way as the button in unit.

¤4TV VOLUME UP ( ) /DOWN ( ) buttons

These buttons increase or decrease TV’s volume.

PROGRAMMING THE REMOTE	ENGLISH
CONTROLLER
The remote controller RC5400SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-
digit code or by scanning the codes until the
correct one is found. We recommend to using the
4-digit code. This mode is faster and more
reliable. The code scanning method should be
used only if you cannot find the code for one of
your appliances. The codes are listed at the end of
this book.
Important:
• U s e t h e r e m o t e c o n t r o l b u t t o n s f o r
programming, not the buttons of the receiver or
other appliances.

•Some codes may be not match your equipment. In this case, your equipment cannot be controlled with this remote controller.

PROGRAMMING WITH THE 4-DIGIT CODE

							OK
	POWER				1.	SETUP/		MENU OFF
						T.TONE
						S-DIRECT	AUTO		DTS
							1	2	3
	TV	VCR1	DSS/VCR2	DVD		NIGHT	CSII	EX/ES	DSP
							4	5	6
						DISPLAY	M-CH ST	STEREO	6.1CH IN
	TUNER	CD	TAPE	CDR/MD			7	8	9
						CLEAR	MEMO	A/D	P.SCAN
					2.			0
		AUX	AMP					CHANNEL/SKIP
1.	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.		BASS	TREBLE	TUNE/SEARCH
							MODE	DISP./RDS	F.DIRECT
	OSD		MENU
						+/A /ANT	–/B /VCR	ATT.	PTY

1. Press and hold down the function button for

the appliance which should be controlled and

press SETUP until the indicator blinks twice.

2. Press the 4-digit code for appliance (code

table at the end of this book)

3. When the procedure is successful, the indicator will blink twice.

Note:

•If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

7