Marantz manual Using the SR4400, → B → C ... Z → 1 → 2 → 3 .... → → +, ← Down

“AUTO PRESET” will appear on the display, and scanning starts from lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.

During this time, the following operations are possible.

• The band can be changed by TUNER button .

4.If no button is pressed during this period, the current station is memorized in location Preset 02

If you wish to skip the current station, press the TUNING button during this period, this station is skipped and auto presetting continues.

5.Operation stops automatically when all 30 preset memory positions are filled or when auto scanning attains the highest endof all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

MANUAL PRESET MEMORY

2. 4.				3.					OK
D RECEIVER SR4400
								SETUP/		MENU OFF
								T.TONE
								S-DIRECT	AUTO		DTS
							3.		1	2	3
								NIGHT	CSII	EX/ES	DSP
									4	5	6
CLEAR	MEMORY		TUNING/PRESET	F/P	MODE
								DISPLAY	M-CH ST	STEREO	6.1CH IN
A/D	HT-EQ			DISPLAY		MUTE	2.		7	8	9
								CLEAR	MEMO	A/D	P.SCAN
6.1 CH-IN		VCR1	CDR/MD	TAPE	CD	TUNER				0
										CHANNEL/SKIP
								BASS	TREBLE	TUNE/SEARCH
									MODE	DISP./RDS	F.DIRECT

(Using the SR4400)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMORY button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing the TUNING or button, while this is still blinking (approx. 5 seconds)

4. Press the MEMORY button again to enter. The display stops blinking.

The station is now stored in the specified preset memory location.

(Using the remote control unit)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote unite. “– –“ (preset number)starts blinking on the display.

3. Enter the desired preset number by pressping numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

	2.				1.			T.TONE
								SETUP/		MENU OFF
								S-DIRECT	AUTO		DTS
							1.		1	2	3
R SR4400								NIGHT	CSII	EX/ES	DSP
									4	5	6
								DISPLAY	M-CH ST	STEREO	6.1CH IN
									7	8	9
								CLEAR	MEMO	A/D	P.SCAN
CLEAR	MEMORY	TUNING/PRESET		F/P	MODE		1.			0
										CHANNEL/SKIP
A/D	HT-EQ			DISPLAY	MUTE
6.1 CH-IN		VCR1	CDR/MD	TAPE	CD	TUNER		BASS	TREBLE	TUNE/SEARCH
									MODE	DISP./RDS	F.DIRECT

(Using the SR4400)

1. Press the F/P button to show the preset station on the display.

2. Select the desired preset station by pressing the TUNINGorbutton on the front panel

(Using the remote control unit)

1. Press the 4 or ¢ button to select the desired preset station, or input your desired preset channel with numeric buttons on the remote.

PRESET SCAN

	SETUP/		MENU OFF
1.	T.TONE
	S-DIRECT	AUTO		DTS
		1	2	3
	NIGHT	CSII	EX/ES	DSP
3.		7	8	9
		4	5	6
3.	DISPLAY	M-CH ST	STEREO	6.1CH IN
	CLEAR	MEMO	A/D	P.SCAN
			0
			CHANNEL/SKIP
3.	BASS	TREBLE	TUNE/SEARCH
		MODE	DISP./RDS	F.DIRECT
	+/A /ANT	–/B /VCR	ATT.	PTY
	DISC/DECK

(Using the remote control unit)

1. Press the P.SCAN on remote.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressping the § continuously.

When the desired preset station is received, cancel the preset scan operation by pressping the CLEAR or P.SCAN.

CLEARING STORED PRESET STATIONS

You can remove preset stations from memory using the following procedure.

		3.	2.			SETUP/		MENU OFF
							1	2	3
						T.TONE
						S-DIRECT	AUTO		DTS
					2.	NIGHT	CSII	EX/ES	DSP
	AV SURROUND RECEIVER SR4400SR4400						7	8	9
							4	5	6
	SURROUND					DISPLAY	M-CH ST	STEREO	6.1CH IN
						CLEAR	MEMO	A/D	P.SCAN
								0
					3.			CHANNEL/SKIP
		CLEARCLEAR	MEMORYMEMORY	TUNING/PRESET
						BASS	TREBLE	TUNE/SEARCH
		A/D	HT-EQ
POWER ON/STANDBY	PHONES	6.1 CHCH--ININ	VCR1		CD		MODE	DISP./RDS	F.DIRECT
						+/A /ANT	–/B /VCR	ATT.	PTY

DISC/DECK

1. Recall the preset number to be cleared with the method described in “RECALLING” a preset station.

2. Press the MEMORY button on the front panel or press MEMO button on the remote.

3. Stored preset number blinks in the display for

5 seconds. While blinking, press the CLEAR button on the front panel or press CLEAR on the remote unit.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Notes:

•To clear stored all preset stations, press and hold the CLEAR and the F/P buttons for two seconds.

NAME INPUT OF THE PRESET STATION.	ENGLISH
This function allows the name of each preset
channel to be entered using alphanumeric
characters.
Before name inputting, need to store preset
stations with the preset memory operation.

4.4. 2. 5. 6. 5.

AVAV SURROUNDSURROUND RECEIVERRECEIVER SR4400SR4400

	SURROUNDSURROUND									V
										DOWN
			CLEARCLEAR	MEMORYMEMORY		TUNING/PRESETTUNING/PRESET		F/P	MODE
			A/D	HT-EQ				DISPLAY		MUTE
POWER ON/STANDBY	PHONES	6.1 CHCH--ININ	TV	DVD	VCR1	DSS/VCR2	CDR/MD	TAPE	CD	TUNER

2. 5. 6.	NIGHT	CSII	EX/ES	DSP
		7	8	9
		4	5	6
3.	DISPLAY	M-CH ST	STEREO	6.1CH IN
	CLEAR	MEMO	A/D	P.SCAN
			0
			CHANNEL/SKIP
5.	BASS	TREBLE	TUNE/SEARCH
		MODE	DISP./RDS	F.DIRECT
4.	+/A /ANT	–/B /VCR	ATT.	PTY
	DISC/DECK

SYSTEM REMOTE CONTROLLER

RC5400SR

1. Recall the preset number to be inputted name with the method described in “RECALLING” a preset station.

2. Press the MEMORY button on the front panel or press MEMO on the remote for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character entry ready status.

4. When the SELECT knob is turned or press 5

/6 button on the remote, alphabetic and numeric characters will be displayed in the

following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

To clear the input charcter, press the CLEAR button on the front panel or on the remote.

5. After selecting the first character to be entered, press the MEMORY button on the front panel, or press MEMO button on the remote.

The entry in this column is fixed and the next column starts to flash. Fill the next column same as.

27