ENGLISH
TROUBLESHOOTING |
| table. |
| ||
|
|
| If the unit does not operate properly, check items shown in the following | ||
|
|
| If your trouble cannot be recovered with the remedy actions listed in | ||
In case of trouble, check the following before calling for service: | |||||
the following table, malfunction of the internal circuitry is suspected; | |||||
1. Are the connections made properly ? | |||||
immediately unplug the power cable and contact your dealer, nearest | |||||
2. Are you operating the unit properly following user’s guide ? | |||||
Marantz distributor or the Marantz Service Center in your country. | |||||
3. Are the power amplifiers and speaker working properly ? | |||||
|
|
|
|
| |
SYMPTOM | CAUSE |
| REMEDY | ||
|
|
|
|
| |
SR9200 cannot be turned up. | The power plug is not connected. |
| Connect the power plug to the outlet. | ||
|
|
|
|
| |
No sound and picture are output | Mute is on. |
| Cancel mute using the remote control unit. | ||
even when power is on. | The input cable is not connected correctly. |
| See the connection diagram and connect the cables correctly. | ||
| The master volume control is turned all the way down. | Adjust the master volume. | |||
| The function selector position is wrong. |
| Select correct position. | ||
|
|
|
| ||
Speaker not outputting any sound. | The headphones are connected to the headphone jack. | Disconnect the headphones. (Speakers will not output sound when | |||
|
|
|
| headphones are connected.) | |
|
|
|
|
| |
Sound and pictures from other | Input cable connected incorrectly. |
| Connect the cable correctly by referring to the connection diagram. | ||
than equipment selected with the |
|
|
|
| |
function selector. |
|
|
|
| |
|
|
|
|
| |
Sound from the wrong channel is | Speaker cable connected incorrectly. |
| Connect the cable correctly by referring to the connection diagram. | ||
output from the speaker. |
|
|
|
| |
|
|
|
| ||
No sound is output from the center | The center speaker cable connection is incomplete. | Connect the cable correctly. | |||
speaker. | STEREO has been selected for Surround mode. |
| When STEREO is selected for Surround mode, no sound will be | ||
| Center = NONE has been selected in SETUP mode. | output from the center speaker. Set another Surround mode. | |||
| Make the correct setting. | ||||
|
|
|
| ||
No sound is output from the | The surround speaker cable connection is incomplete. | Connect the cable correctly. | |||
surround speaker. | STEREO has been selected for Surround mode. |
| When STEREO has been selected for Surround mode, no sound will | ||
| Surround = NONE has been selected in SETUP mode. | be output from the surround speaker. Set another Surround mode. | |||
| Make the correct setting. | ||||
|
|
|
| ||
No output to Sub Woofer Out. | Select | ||||
|
|
|
|
| |
S u r r o u n d m o d e c a n n o t b e | The headphones are connected to the jack. |
| Disconnect the headphones. (When headphones are connected, | ||
changed. |
|
|
| Surround mode will be fixed to STEREO.) | |
|
|
|
|
| |
Noise is produced during DTS- | Analog has been selected for input. |
| Be sure to perform digital connection, select digital input, then play. | ||
encoded CD or laser disc play. |
|
|
|
| |
|
|
|
|
| |
DTS sources cannot be played. | Surround mode is set to DOLBY. |
| Select other mode. | ||
| The DVD or LD player is not DTS digital out capable. | Use a player which responds to | |||
|
|
|
|
| |
Player skips during play of a DTS | Data error occurred during player skip. |
| Set Surround mode to | ||
source and produces noise. |
|
|
|
| |
|
|
|
| ||
A 96kHz PCM signal cannot be | The disc player is not 96kHz PCM digital out capable. | Use a player that responds to 96kHz PCM digital out. | |||
played. | Surround mode is set to other than STEREO and AUTO. | Set Surround mode to STEREO or AUTO. | |||
|
|
|
| ||
A normal PCM signal (CD or laser | Surround mode is set to | Select other mode. | |||
disc) cannot be played. | ES. |
|
| ||
|
|
|
| ||
A Dolby Digital signal cannot be | Surround mode is set to | Select other mode. | |||
played. | ES. |
|
| ||
|
|
|
|
| |
A specific channel does not | Nothing recorded on source. |
| Check the encoded channel on the source side. | ||
produce output. |
|
|
|
| |
|
|
|
|
| |
FM or AM reception fails. | Antenna connection is incomplete. |
| Correctly connect the indoor FM and AM antennas to FM and AM | ||
|
|
|
| antenna outlets. | |
|
|
|
|
| |
Noise is heard during AM reception. | Reception is affected by other electrical fields. |
| Try changing location where the AM indoor antenna is set up. | ||
|
|
|
| ||
Noise is heard during FM reception. | The radio waves from the broadcasting station are weak. | Install an FM outdoor antenna or use cable TV/FM. | |||
|
|
|
|
| |
Cannot get programmed station | Preset data has been erased. |
| Disconnecting power plug for long periods of time will erase preset | ||
when the PRESET button is |
|
|
| data. If that happens, input the preset data again. | |
pressed. |
|
|
|
| |
|
|
|
|
| |
Nothing appears on the remote | Batteries are consumed. |
| Replace all the batteries with new ones. | ||
commander display. |
|
|
|
| |
|
|
|
|
| |
Control with the remote control | Batteries are consumed.. |
| Replace all the batteries with new ones.. | ||
unit fails. | Remote controller's |
| Select different position from which equipment will be controlled. | ||
| The distance between this SR9200 and the remote | Move closer to this SR9200. | |||
| commander is too far. |
|
| ||
| S o m e t h i n g i s b l o c k i n g S R 9 2 0 0 a n d t h e r e m o t e | Remove offending object. | |||
| commander. |
|
| ||
|
|
| |||
No sound is output from the | The surround speaker cable connection is incomplete. | Connect the cable correctly. | |||
surround back speaker. | STEREO has been selected for Surround mode. |
| Surround back channel is active in THX surround EX mode, in other | ||
| Surr. Back = NONE has been selected in SETUP mode. | Surround mode, no sound will be output from the surround speaker. | |||
| surround back speaker. |
|
| ||
| Surround mode is not THX surround EX. |
| Set THX Surround EX mode. | ||
|
|
|
| ||
Can not decode HDCD. | Input signal does not support HDCD. |
| Play HDCD CD . | ||
| Surround mode is not AUTO, or Source Direct. |
| Set surround mode AUTO or Source Direct. | ||
|
|
|
|
|
46