Marantz SR9600 manual Link Audio, Display does not Connected monitor or Appear over an Hdmi

ENGLISH

HDMI

SYMPTOM	CAUSE		REMEDY
The display does not	The connected monitor or
appear over an HDMI	projector does not support HDCP.
connection.
	The HDMI input of on the TV is	Set HDMI input so that it turns on, as
	not on.	explained in the TV's instruction manual.
	The HDMI output on the source	Set HDMI output so that it turns on, as
	component (DVD, Set Top Box,	explained in the source component's
	etc.) is not on.	instruction manual.
	The HDMI mode is not correctly	Set HDMI input on the FUNC INPUT
	set on the SR9600.	SETUP menu as explained on page 33.
	The HDMI output video resolution	Set the resolution so that it matches, as
	of the source component (DVD,	explained in the instruction manuals of
	Set Top Box, etc.) does not	both components.
	match the TV specifications.
	The device is connected with a	A 5 m or shorter cable is recommended
	non-standard HDMI cable.	to ensure stable operation and prevent
		image quality deterioration.
	Power to the SR9600 is off.	Turn on the power to the SR9600.
	(When the SR9600 is on
	standby, HDMI connections
	cannot be turned on.)
	The connection between HDMI	Shut off and then turn the power back on
	components was not	to the SR9600, TV and source
	authenticated.	component.
The SR9600 SETUP	The SR9600 SETUP menu	Use the COMPONENT VIDEO, S-VIDEO
menu does not appear	does not support HDMI output.	or VIDEO output.
over an HDMI connection.
Time is needed for the	The connection is being	There is nothing wrong with the system.
display of an HDMI	authenticated between the	Some HDMI devices require time for
connection to appear.	HDMI devices.	authentication.
Audio is not played back	The HDMI audio output of the	Set the HDMI audio output so that it turns
over an HDMI	source component (DVD, Set	on, as explained in the source
connection.	Top Box, etc.) is not on.	component's instruction manual.
	The signal format of the source	Set the HDMI audio output so that it can
	component (DVD, Set Top Box,	connect to the SR9600, as explained in
	etc.) is not supported by the	the source component's instruction
	SR9600.	manual.
	The SR9600 is set to the HDMI	In the “THROUGH” mode, sound is not
	audio “THROUGH” mode.	produced from the SR9600. Set it to
		“ENABLE”. (see page 44)
DVD-Audio is not played	The DVD player does not	•	Use a DVD-Audio player that supports
back over an HDMI	support CPPM, therefore it		CPPM.
connection.	cannot output HDMI audio.	•	Turn on PCM downsampling on the
			DVD player.
		•	Use an analog connection.

SYMPTOM	CAUSE	REMEDY
Super Audio CD is not	The current HDMI connection	Use an analog connection.
played back over an	does not support Super Audio
HDMI connection.	CDs.

i.LINK (AUDIO)

SYMPTOM	CAUSE	REMEDY
Audio is not played back	The connected component	Use a component that supports i.LINK
over an i.LINK	does not support i.LINK	(Audio).
connection.	(Audio).
	The connected component	Use a device that supports DTCP.
	does not support DTCP (Digital
	Transmission Content
	Protection).
	The i.LINK mode on the	Set i.LINK input on the SETUP menu as
	SR9600 is not correctly set.	explained on page 34.
	The i.LINK output of the source	Set i.LINK output so that it turns on, as
	component (DVD, etc.) is not on.	explained in the source component
		instruction manual.
	Power to one of the	Turn on power to all devices in the i.LINK
	components in a daisy chain or	connection.
	tree connection is not on.
	There are too many i.LINK	Disconnect unused i.LINK devices.
	devices outputting signals on the
	i.LINK bus.
Audio is not played back	Authentication is being	There is nothing wrong with the system.
for a few seconds when	performed for copyright	Some components require time for
the input source is	protection.	authentication.
changed or the power is
shut off and turned back
on.
The analog audio of the	Components disable analog	Change the i.LINK setting on the
connected component is	output when an i.LINK	component.
not played back over	connection is on.
i.LINK.
The digital output of the	Components disable digital	Change the i.LINK setting on the
connected component is	output when an i.LINK	component.
not played back over	connection is on.
i.LINK.

64