MaxTech V.32bis, V.42bis Section Five - Result Codes

13

Table 4-1 S - Registers

Register Function Range/units Default

S0 Auto-answer Ring 0-255/rings 0

S1 Ring counter 0-255/rings 0

S2 Escape code character 0-127/ASCII 43

S3 Carriage return character 0-127/ASCII 13

S4 Line feed character 0-127/ASCII 10

S5 Backspace character 0-32, 127/ASCII 8

S6 Dial tone wait time 0-255/seconds 2

S7 Remote carrier wait time 1-255/seconds 30

S8 Comma pause time 0-255/seconds 2

S9 Carrier detect time 0-255/0.1 second 6

S10 Carrier loss time 0-255/0.1 second 14

S11 Touch-tone dialing speed 50-255/0.001 second 70

S12 Esc. character detect time 0-255/0.02 second 50

S13 Reserved

S14 Echo, response, dialing, Bit-mapped

originate/answer

S15 Reserved

S16 Modem test options Bit-mapped

S17 Reserved

S18 Modem test timer 0-255/seconds 0

S19 Reserved

S20 Reserved

S21 DTR, DCD, DSR, and Bit-mapped

Long Space Disconnect

S22 Speaker and response Bit-mapped

S23 RDL, DTE data rate, Bit-mapped

parity,and guard tone

S24 Reserved

S25 DTR delay 0-100/seconds 5

S26 RTS/CTS delay interval 0-255/0.01 second 1

S27 Async operation, CCITT/ Bit-mapped

Bell mode

S28 Reserved

S29 Reserved

S30 Sleep mode time 0-90/seconds 10

S37 Maximum line speed 0-11 0

S90 Disconnect timer 0-255/seconds 0

S108 Retrain options 0-3 2

S109 Line Speed permitted 2-62 62

Section Five - Result Codes

Contents

Main User's Manual 1 Section One - Introduction Figure 2-1 Common Serial Ports Section Two - Installation 2.1 Unpacking Your Modem 2.2 Hardware Installation 2 2.3 Software Installation/Configuration Figure 2-2 Expansion Slots Page 4 2.4 COM Port and Interrupt Settings SW-1 Table 2-1 Switch Block Settings Figure 2-3 Switch Block SW-1 Location 5 2.5 Using Fax, Voice, and Speakerphone Capabilities of the Modem 2.6 Testing Your Modem After Installation 2.7 Using Your Modem 6 Section Three - AT Command Set 3.1 Executing Commands 3.2 Command Structure 7 3.3 Basic AT Commands In the following listings, all default settings are printed in bold text. Command Function 8 3.4 Extended AT Commands Page 10 3.5 MNP/V.42/V.42bis Commands 11 3.6 Fax Class 1 Commands 12 3.7 Voice Mode Commands Setion Four - S Registers 13 Table 4-1 S - Registers Register Function Range/units Default Section Five - Result Codes 14 BASIC RESPONSE CODES MODIFIED RESPONSE CODES (\V1) EXTENDED RESPONSE CODES (\V2) 15 Section Six - Troubleshooting Modem does not respond to commands. Modem does not dial. Modem dials but does not connect. Page 17 Section Seven - Specifications Section Eight - Support and Service Section Nine - FCC , DOC & Other Notices 9.1 FCC Compliance 18 9.2 FCC Class B Statement 9.3 DOC Compliance Information 19 9.4 Disclaimer, Copyright, And Other Notices 1 Section One - Introduction Figure 2-1 Common Serial Ports Section Two - Installation 2.1 Unpacking Your Modem 2.2 Hardware Installation 2 2.3 Software Installation/Configuration Figure 2-2 Expansion Slots 3 2.4 COM Port and Interrupt Settings Page 5 2.6 Testing Your Modem After Installation 2.7 Using Your Modem 2.8 Where To Go From Here 6 Section Three - AT Command Set 3.1 Executing Commands 3.2 Command Structure 3.3 Basic AT Commands Page 8 3.4 Extended AT Commands 9 3.5 MNP/V.42/V.42bis Commands Page 11 3.6 Fax Class 1 Commands 3.7 Voice Mode Commands 12 Setion Four - S Registers Table 4-1 S - Registers Register Function Range/units Default 13 Section Five - Result Codes BASIC RESPONSE CODES MODIFIED RESPONSE CODES (\V1) EXTENDED RESPONSE CODES (\V2) 14 Section Six - Troubleshooting Modem does not respond to commands. 15 Modem does not dial. Modem dials but does not connect. Modem makes a connection but no data appears on your screen. High pitch tone is heard whenever you answer the phone. Section Seven - Specifications 17 Section Eight - Support and Service Section Nine - FCC , DOC & Other Notices 9.1 FCC Compliance 9.2 FCC Class B Statement 18 9.3 DOC Compliance Information 19 9.4 Disclaimer, Copyright, And Other Notices