Dryer Dimensions
22z/4''
43%"
(110cm)
*27aA,,
(70.5cm)
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:
•Additional spacing should be considered for ease of installation and servicing.
•Additional clearances might be required for wall, door and floor moldings.
•Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
•For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. [ ouvered doors with equivalent ventilation openings are acceptable.
It is your responsibility
•[b contact a qualified electrical installer.
•[b be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA
The National Electric Code requires a
after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.
lb supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate)
on a separate
breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.
•Companion appliance spacing should also be considered.
|
|
|
|
|
|
|
|
|
|
|
| _. 3"* |
|
|
|
|
|
|
|
|
|
|
|
| (7.6crn) |
|
|
| 18,,*_1C |
|
|
|
|
|
|
| ||
|
|
| (45.cm)7 |
|
|
|
|
|
|
| ||
|
|
|
| _L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3,J* |
|
|
|
|
|
|
|
|
|
|
|
| (7.6¢m) |
|
|
|
| 1" |
|
|
|
|
|
| 3- | |
|
|
| (2.5cm) |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| C |
|
|
|
|
|
|
|
| A. | Recessed | area |
| |
|
|
|
|
|
|
|
| B. Side view - closet or confined area | ||||
|
|
|
|
|
|
|
| (7. Closet | door | with vents | ||
*Required | spacing |
|
|
|
|
|
|
|
|
| ||
Mobile | Home | - | Additional | Installation | Requirements |
| ||||||
This dryer | is suitable | for | mobile | home | installations. | The | installation must conform to the | |||||
Manufactured | Home | Construction | and | Safety Standard, Title 24 CFR, Part 3280 (formerly the | ||||||||
Federal | Standard | for | Mobile Home Construction | and Safety, Title 24, HUD Part 280) or the | ||||||||
Canadian |
| Manufactured | Home | Standard, | MH. | |||||||
Mobile | home | installations | require: |
|
|
|
| |||||
•Metal exhaust system hardware, which is aw_ilable for purchase frorn your dealer.
•Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.
•Do not use an extension cord.
•If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
Electrical Connection
[b properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
•[his dryer is manufactured ready to install with a
or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.
.... | 5 |
