| PARTS LIST (Cont'd) |
|
|
31 | Bowl Assembly SS/Black | 03.6523.00 | 1 |
32 | Hood Assembly 430 SS/Silver | 03.6524.00 | 1 |
33 | Hood Assembly 430 SS/Black | 03.6524.01 | 1 |
34 | Spring Pin, Hood Hinge | 03.6525.00 | 2 |
35 | Clevis Pin, Hood Hinge | 03.6526.00 | 2 |
36 | Side Table, Left Burner SS/Silver | 03.6527.00 | 1 |
37 | Side Table, Left Burner SS/Black | 03.6527.01 | 1 |
38 | Screw, M4x15mm (Side Table Front) | 03.6528.00 | 4 |
39 | Side Table, Right SS/Silver | 03.6529.00 | 1 |
40 | Side Table, Right SS/Black | 03.6529.01 | 1 |
41 | Valve, Side Burner | 03.6530.00 | 1 |
42 | Screw, M5x10mm (Side Burner Valve Bracket) | 03.6531.00 | 2 |
43 | Nut, M5 Hex | 03.6532.00 | 2 |
44 | Side Burner & Venturi | 03.6533.00 | 1 |
45 | Screw, M4x8mm (Side Burner & Door Handle) | 03.6534.00 | 6 |
46 | Electrode Wire, Side Burner | 03.6535.00 | 1 |
47 | Knob, Control (Main & Side Burners) | 03.6401.00 | 5 |
48 | Grid, Side Burner | 03.6407.00 | 1 |
49 | Main Burner, Cast Iron | 03.6447.00 | 4 |
50 | Burner Pin, Main Burner | 03.5012.00 | 4 |
51 | Pan, Foil | Local Purchase | 1 |
52 | Pan, Grease | 03.6402.00 | 1 |
53 | Drip Tray | 03.5998.00 | 1 |
54 | Flame Diffuser SS | 03.6536.00 | 4 |
55 | Cooking Grid | 03.5023.00 | 2 |
56 | Warming Rack | 03.6449.00 | 1 |
57 | Ignition Box | 03.6421.00 | 1 |
58 | Shim, Ignition Box | 03.6423.00 | 1 |
59 | Regulator/Hose | 03.6537.00 | 1 |
60 | Ignitor Switch | 03.6426.00 | 1 |
61 | Heat Indicator | 03.5033.00 | 1 |
62 | Electrode, Main Burner | 03.6427.00 | 2 |
63 | Manifold Assembly (LP) | 03.6450.01 | 1 |
64 | Left Door, Silver | 03.6443.02 | 1 |
65 | Right Door, Silver | 03.6444.02 | 1 |
TOOLS REQUIRED:
Phillips Screwdriver | Pliers | or Wrench | |
|
|
|
|
|
|
|
|
To reduce the risk of a cut injury:
·Wear protective gloves when handling parts that have sharp edges.
STEP 1) Cylinder Clamp/Back Panel Assembly:
Lay Back Panel (2/3) on floor. (FIG. 1A) Attach LP Cylinder Clamp (4) to Back Panel by squeezing clamp together to fit into the two slotted openings; then release. (FIG. 1B) Make sure the large loop is down against the panel.
(4) LP CYLINDER | FIG. 1B |
CLAMP |
(2/3) BACK PANEL
5FIG. 1A
