Manuals / Brands / Computer Equipment / Power Supply / MGE UPS Systems / Computer Equipment / Power Supply

MGE UPS Systems AmpMeter PDU TCP/IP Administration, To create a infeed name:, To display the firmware version:, To perform a warm boot:, To set the IP address:

1 52

Download 52 pages, 1.05 Mb

3. Operations

Creating a descriptive infeed name

The Set Infeed Name command assigns a descriptive name to an infeed. This descriptive name is displayed when the Show Traps command is issued.

To create a infeed name:

At the AmpMeter PDU: prompt, type set infeed name, followed by the absolute infeed name, then the descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal - spaces are not allowed). Press Enter.

Example

The following command adds the descriptive name HQ_1_Infeed_A to the infeed on the AmpMeter PDU:

AmpMeter PDU: set infeed name .aa HQ_1_Infeed_A<Enter>

Displaying Infeed information

The Show Infeeds command displays information about all infeeds. This information includes the absolute and descriptive infeed names.

To display tower information:

At the AmpMeter PDU: prompt, type show infeeds and press Enter.

Example

AmpMeter PDU: show infeeds<Enter>

Input Input Feed ID Feed Name

.AA HQ_1_Infeed_A

.AB HQ_1_Infeed_B

.BA HQ_2_Infeed_A

.BB HQ_2_Infeed_B

Displaying the firmware version

The Version command displays the firmware version.

To display the firmware version:

At the AmpMeter PDU: prompt, type version and press Enter.

Performing a warm boot

The Restart command performs a warm boot of the AmpMeter PDU.

NOTE: System user/outlet/group/port configuration or outlet states are NOT changed or reset with this command.

To perform a warm boot:

At the AmpMeter PDU: prompt, type restart and press Enter.

TCP/IP Administration

NOTE: A restart of the AmpMeter PDU is required after setting or changing ANY TCP/IP configurations. See Performing a warm boot on page 28 for more information.

Setting the IP address

The Set Ipaddress command sets the TCP/IP address of the network interface controller.

To set the IP address:

At the AmpMeter PDU: prompt, type set ipaddress, followed by the IP address and press Enter.

Example

The following command sets the IP address to 12.34.56.78:

AmpMeter PDU: set ipaddress 12.34.56.78<Enter>

Page 28 - 301-0399-3 Rev B.

Contents

AmpMeter PDU Installation and user manual Instructions Dangerous Voltage Protective Grounding Terminal Life-SupportPolicy Compliance GETTING STARTED INSTALLATION OPERATIONS ADVANCED OPERATIONS APPENDICES Quick Start Guide Standard Accessories Additional Required Items Equipment Overview Figure 0.1 AmpMeter PDU Views Safety Precautions Installing the Power Input Retention Bracket Figure 2. Retention Bracket assembly Mounting Figure 3. Mounting Horizontal/Rack Vertical/Tower Connecting to the Power Source Connecting Devices Connecting the Sensors Connecting to the Unit (Remote Monitoring Units Only) Serial (RS232) port Ethernet port INTERFACES HTML INTERFACE COMMAND LINE INTERFACE Interfaces Usernames and Passwords HTML Interface Figure 4. Example HTML page Environmental Monitoring Input Load Sensors Configuration System Network Telnet/SSH HTTP/SSL Serial Ports Users FTP SNTP SNMP Tools Restart Command Line Interface Operations Command Summary Administrative Command Summary Administrative Command Summary (continued) Operations Commands To display accessible serial ports: Example To display status of one or more infeeds: Examples To display the status of the Environmental Monitor: To start a new session: To end a session: Administration Commands User Administration To create a user account: To remove a user account: To change a password: To set the access level privilege for a user: To grant or remove input status viewing privileges for a user: To display user access privilege levels: To grant serial port access to a user: To delete serial port access for a user: To display user serial port access: Serial Port Administration To create a port name: To set the serial port data-rate: To enable or disable active signal checking for serial connections: To display serial port information: System Administration To create a location description: To display system configuration information: To create a tower name: To display tower information: To create a infeed name: To display the firmware version: TCP/IP Administration To set the IP address: To set the subnet mask: To set the gateway IP address: To display network configuration information: HTTP Administration To enable or disable HTTP support: To change the HTTP port: To set the HTTP authentication method: Telnet Administration FTP Administration To set the FTP Host IP address: To set the FTP username: To set the FTP password: To set the FTP filename: SNTP Administration To set the SNTP server address: To display SNTP configuration information SSL SSH SNMP SSL SSL Command Summary Enabling and Setting up SSL Support To enable or disable SSL support: To change the access level: SSH SSH Command Summary Enabling and Setting up SSH Support To enable or disable SSH support: To change the SSH port: SNMP SNMP Command Summary Enabling and Setting up SNMP Support To enable SNMP support: To set the trap destination: To set the trap timer: To set the Setcomm community string: To set the Getcomm community string: To set the Trapcomm community string: To display SNMP configuration information: SNMP Traps Trap Summary Tower Status traps Infeed Status traps Environmental Monitor Status traps Temperature/Humidity Sensor Status traps Load traps Temp traps Humidity traps Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trap: To Enable or Disable a Load trap: To set the infeed load limit: To Enable or Disable a Change trap: To Enable or Disable the Temp trap: To set the Temperature threshold limits: To Enable or Disable the Humid trap: To set the Humidity threshold limits: To display trap information: RESETTING TO FACTORY DEFAULTS UPLOADING FIRMWARE TECHNICAL SPECIFICATIONS Resetting to Factory Defaults To reset to factory defaults from the HTML interface To reset to factory defaults from the command line To reset to factory defaults using the reset button Uploading Firmware Technical Specifications Models Europe/Asia Americas Power Ratings Physical Specifications Data Connections Branch Circuit Protection