Manuals / Brands / Computer Equipment / Power Supply / MGE UPS Systems / Computer Equipment / Power Supply

MGE UPS Systems AmpMeter PDU To display system configuration information:, To create a tower name:, To display tower information:, Enter, Enter, Enter, Example, Example, Examples

1 52

Download 52 pages, 1.05 Mb

3. Operations

Displaying system configuration information

The Show System command displays all system configuration information.

•Firmware version

•NIC module serial number and MAC address

•Hardware revision code and Flash size

•Uptime since last system restart

•System location description

See 0on page 32 for more information on SNMP.

To display system configuration information:

At the AmpMeter PDU: prompt, type show system and press Enter.

Example

System	Information
F/W	Version:	AmpMeter PDU Version 5.2i
NIC	S/N:	1600001
MAC	Address:	00-0a-9c-10-00-01
H/W	Rev Code:	0	MB
Flash Size:		1	MB	minutes 1 second
Uptime:		0	days 6 hours 14	minutes 1 second

Location: Florida HQ

Creating a descriptive tower name

The Set Tower Name command assigns a descriptive name to a tower. This descriptive name is displayed when the Show Traps command is issued. See ??? on page 28 for more information on the Show Traps command.

To create a tower name:

At the AmpMeter PDU: prompt, type set tower name, followed by the absolute tower name, then the descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal - spaces are not allowed). Press Enter.

Examples

The following command adds the descriptive name Florida_HQ_1 to tower .a:

AmpMeter PDU: set tower name .a Florida_HQ_1<Enter>

Displaying tower information

The Show Towers command displays information about the AmpMeter PDU. This information includes the absolute and descriptive AmpMeter PDU names.

To display tower information:

At the AmpMeter PDU: prompt, type show towers and press Enter.

Example

AmpMeter PDU: show towers<Enter>

Tower Tower

ID Name

.A Florida_HQ_1

301-0399-3 Rev B. - Page 27

Contents

AmpMeter PDU Installation and user manual Instructions Dangerous Voltage Protective Grounding Terminal Life-SupportPolicy Compliance GETTING STARTED INSTALLATION OPERATIONS ADVANCED OPERATIONS APPENDICES Quick Start Guide Standard Accessories Additional Required Items Equipment Overview Figure 0.1 AmpMeter PDU Views Safety Precautions Installing the Power Input Retention Bracket Figure 2. Retention Bracket assembly Mounting Figure 3. Mounting Horizontal/Rack Vertical/Tower Connecting to the Power Source Connecting Devices Connecting the Sensors Connecting to the Unit (Remote Monitoring Units Only) Serial (RS232) port Ethernet port INTERFACES HTML INTERFACE COMMAND LINE INTERFACE Interfaces Usernames and Passwords HTML Interface Figure 4. Example HTML page Environmental Monitoring Input Load Sensors Configuration System Network Telnet/SSH HTTP/SSL Serial Ports Users FTP SNTP SNMP Tools Restart Command Line Interface Operations Command Summary Administrative Command Summary Administrative Command Summary (continued) Operations Commands To display accessible serial ports: Example To display status of one or more infeeds: Examples To display the status of the Environmental Monitor: To start a new session: To end a session: Administration Commands User Administration To create a user account: To remove a user account: To change a password: To set the access level privilege for a user: To grant or remove input status viewing privileges for a user: To display user access privilege levels: To grant serial port access to a user: To delete serial port access for a user: To display user serial port access: Serial Port Administration To create a port name: To set the serial port data-rate: To enable or disable active signal checking for serial connections: To display serial port information: System Administration To create a location description: To display system configuration information: To create a tower name: To display tower information: To create a infeed name: To display the firmware version: TCP/IP Administration To set the IP address: To set the subnet mask: To set the gateway IP address: To display network configuration information: HTTP Administration To enable or disable HTTP support: To change the HTTP port: To set the HTTP authentication method: Telnet Administration FTP Administration To set the FTP Host IP address: To set the FTP username: To set the FTP password: To set the FTP filename: SNTP Administration To set the SNTP server address: To display SNTP configuration information SSL SSH SNMP SSL SSL Command Summary Enabling and Setting up SSL Support To enable or disable SSL support: To change the access level: SSH SSH Command Summary Enabling and Setting up SSH Support To enable or disable SSH support: To change the SSH port: SNMP SNMP Command Summary Enabling and Setting up SNMP Support To enable SNMP support: To set the trap destination: To set the trap timer: To set the Setcomm community string: To set the Getcomm community string: To set the Trapcomm community string: To display SNMP configuration information: SNMP Traps Trap Summary Tower Status traps Infeed Status traps Environmental Monitor Status traps Temperature/Humidity Sensor Status traps Load traps Temp traps Humidity traps Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trap: To Enable or Disable a Load trap: To set the infeed load limit: To Enable or Disable a Change trap: To Enable or Disable the Temp trap: To set the Temperature threshold limits: To Enable or Disable the Humid trap: To set the Humidity threshold limits: To display trap information: RESETTING TO FACTORY DEFAULTS UPLOADING FIRMWARE TECHNICAL SPECIFICATIONS Resetting to Factory Defaults To reset to factory defaults from the HTML interface To reset to factory defaults from the command line To reset to factory defaults using the reset button Uploading Firmware Technical Specifications Models Europe/Asia Americas Power Ratings Physical Specifications Data Connections Branch Circuit Protection