Manuals / Brands / Computer Equipment / Power Supply / MGE UPS Systems / Computer Equipment / Power Supply

MGE UPS Systems AmpMeter PDU SNMP, SNMP Command Summary, Enabling and Setting up SNMP Support, To enable SNMP support:, To set the trap destination:, To reset the trap destination:

1 52

Download 52 pages, 1.05 Mb

4. Advanced Operations

SNMP

The AmpMeter PDU family of products supports the Simple Network Management Protocol (SNMP). This allows network management systems to use SNMP requests to retrieve information and control power for the individual outlets.

The AmpMeter PDU includes an SNMP v1 agent supporting standard MIB I and MIB II objects.

NOTE: For security, SNMP support is disabled by default.

SNMP Command Summary

Command	Description
Set snmp	Enables or disables SNMP support

Set snmp getcomm	Sets the ‘get’ community string

Set snmp setcomm	Sets the ‘set’ community string

Set snmp trapdest1	Sets a destination IP addresses for traps

Set snmp trapdest2	Sets a destination IP addresses for traps

Set snmp traptime	Sets the delay for steady state condition traps

Show snmp	Displays all SNMP configuration information

Enabling and Setting up SNMP Support

AmpMeter PDU SNMP support must be enabled and configured for access to AmpMeter PDU3 MIB objects and generation of all AmpMeter PDU3 traps.

Enabling/disabling SNMP support

The AmpMeter PDU SNMP command is used to enable or disable SNMP support.

To enable SNMP support:

At the AmpMeter PDU: prompt, type set snmp, followed by enabled or disabled and press Enter.

NOTE: A restart of the AmpMeter PDU is required after enabling or disabling SNMP support. See Performing a warm boot on page 28 for more information.

Setting trap destinations

The Set SNMP Trapdest1 and Trapdest2 commands are used to set the IP addresses of SNMP management stations receiving all traps. AmpMeter PDU supports a maximum of two trap destinations; one must be defined to enable trap generation.

To set the trap destination:

At the AmpMeter PDU: prompt, type set snmp, trapdest1 or trapdest2, the Ipaddress and press Enter.

Example

The following sets the trap destination 1 to 64.42.31.208:

AmpMeter PDU: set snmp trapdest1 64.42.31.208<Enter>

To reset the trap destination:

At the AmpMeter PDU: prompt, type set snmp, trapdest1 or trapdest2, 0.0.0.0 and press Enter.

Page 36 - 301-0399-3 Rev B.

Contents

AmpMeter PDU Installation and user manual Instructions Dangerous Voltage Protective Grounding Terminal Life-SupportPolicy Compliance GETTING STARTED INSTALLATION OPERATIONS ADVANCED OPERATIONS APPENDICES Quick Start Guide Standard Accessories Additional Required Items Equipment Overview Figure 0.1 AmpMeter PDU Views Safety Precautions Installing the Power Input Retention Bracket Figure 2. Retention Bracket assembly Mounting Figure 3. Mounting Horizontal/Rack Vertical/Tower Connecting to the Power Source Connecting Devices Connecting the Sensors Connecting to the Unit (Remote Monitoring Units Only) Serial (RS232) port Ethernet port INTERFACES HTML INTERFACE COMMAND LINE INTERFACE Interfaces Usernames and Passwords HTML Interface Figure 4. Example HTML page Environmental Monitoring Input Load Sensors Configuration System Network Telnet/SSH HTTP/SSL Serial Ports Users FTP SNTP SNMP Tools Restart Command Line Interface Operations Command Summary Administrative Command Summary Administrative Command Summary (continued) Operations Commands To display accessible serial ports: Example To display status of one or more infeeds: Examples To display the status of the Environmental Monitor: To start a new session: To end a session: Administration Commands User Administration To create a user account: To remove a user account: To change a password: To set the access level privilege for a user: To grant or remove input status viewing privileges for a user: To display user access privilege levels: To grant serial port access to a user: To delete serial port access for a user: To display user serial port access: Serial Port Administration To create a port name: To set the serial port data-rate: To enable or disable active signal checking for serial connections: To display serial port information: System Administration To create a location description: To display system configuration information: To create a tower name: To display tower information: To create a infeed name: To display the firmware version: TCP/IP Administration To set the IP address: To set the subnet mask: To set the gateway IP address: To display network configuration information: HTTP Administration To enable or disable HTTP support: To change the HTTP port: To set the HTTP authentication method: Telnet Administration FTP Administration To set the FTP Host IP address: To set the FTP username: To set the FTP password: To set the FTP filename: SNTP Administration To set the SNTP server address: To display SNTP configuration information SSL SSH SNMP SSL SSL Command Summary Enabling and Setting up SSL Support To enable or disable SSL support: To change the access level: SSH SSH Command Summary Enabling and Setting up SSH Support To enable or disable SSH support: To change the SSH port: SNMP SNMP Command Summary Enabling and Setting up SNMP Support To enable SNMP support: To set the trap destination: To set the trap timer: To set the Setcomm community string: To set the Getcomm community string: To set the Trapcomm community string: To display SNMP configuration information: SNMP Traps Trap Summary Tower Status traps Infeed Status traps Environmental Monitor Status traps Temperature/Humidity Sensor Status traps Load traps Temp traps Humidity traps Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trap: To Enable or Disable a Load trap: To set the infeed load limit: To Enable or Disable a Change trap: To Enable or Disable the Temp trap: To set the Temperature threshold limits: To Enable or Disable the Humid trap: To set the Humidity threshold limits: To display trap information: RESETTING TO FACTORY DEFAULTS UPLOADING FIRMWARE TECHNICAL SPECIFICATIONS Resetting to Factory Defaults To reset to factory defaults from the HTML interface To reset to factory defaults from the command line To reset to factory defaults using the reset button Uploading Firmware Technical Specifications Models Europe/Asia Americas Power Ratings Physical Specifications Data Connections Branch Circuit Protection