Manuals / Brands / Computer Equipment / Power Supply / MGE UPS Systems / Computer Equipment / Power Supply

MGE UPS Systems AmpMeter PDU To set the subnet mask:, To set the gateway IP address:, To display network configuration information:, Enter, Enter, Enter, Example, Example, Example

1 52

Download 52 pages, 1.05 Mb

3. Operations

Setting the subnet mask

The Set Subnet command sets the subnet mask for the network the PT40 will be attached to.

To set the subnet mask:

At the AmpMeter PDU: prompt, type set subnet, followed by the subnet mask and press Enter.

Example

The following command sets the subnet mask to 255.0.0.0

AmpMeter PDU: set subnet 255.0.0.0<Enter>

Setting the gateway

The Set Gateway command sets the IP address of the default gateway the AmpMeter PDU uses to access external networks.

To set the gateway IP address:

At the AmpMeter PDU: prompt, type set gateway, followed by the gateway IP address and press Enter.

Example

The following command set the gateway IP address to 12.34.56.1:

AmpMeter PDU: set gateway 12.34.56.1<Enter>

Displaying network configuration information

The Show Network command displays TCP/IP, Telnet, SSH, Web, SSL and SNMP configuration information.

•IP address, subnet mask and gateway

•Enabled-disabled status of Telnet, SSH, HTTP,SSL and SNMP support

•Telnet, SSH, and HTTP port numbers

•HTTP authentication method and SSL access setting

•Network status

See page 32 for more information on SNMP and Secure Proxy

To display network configuration information:

At the AmpMeter PDU: prompt, type show network and press Enter.

Example

The following command displays the network configuration information:

AmpMeter PDU: show network<Enter>

Network Configuration

IP Address:	12.34.56.78
Subnet Mask:	255.0.0.0
Gateway:	12.34.56.1
Telnet:	Enabled	Port:	23
SSH:	Enabled	Port: 65535		Security: BASIC
HTTP:	Enabled	Port:	80	Security: BASIC
SSL:	Enabled			Access:	Required
SNMP:	Enabled
Network Status
Link:	Up
Speed:	100 Mbps
Duplex:	Full
Negotiation:	Auto

301-0399-3 Rev B. - Page 29

Contents

AmpMeter PDU Installation and user manual Instructions Dangerous Voltage Protective Grounding Terminal Life-SupportPolicy Compliance GETTING STARTED INSTALLATION OPERATIONS ADVANCED OPERATIONS APPENDICES Quick Start Guide Standard Accessories Additional Required Items Equipment Overview Figure 0.1 AmpMeter PDU Views Safety Precautions Installing the Power Input Retention Bracket Figure 2. Retention Bracket assembly Mounting Figure 3. Mounting Horizontal/Rack Vertical/Tower Connecting to the Power Source Connecting Devices Connecting the Sensors Connecting to the Unit (Remote Monitoring Units Only) Serial (RS232) port Ethernet port INTERFACES HTML INTERFACE COMMAND LINE INTERFACE Interfaces Usernames and Passwords HTML Interface Figure 4. Example HTML page Environmental Monitoring Input Load Sensors Configuration System Network Telnet/SSH HTTP/SSL Serial Ports Users FTP SNTP SNMP Tools Restart Command Line Interface Operations Command Summary Administrative Command Summary Administrative Command Summary (continued) Operations Commands To display accessible serial ports: Example To display status of one or more infeeds: Examples To display the status of the Environmental Monitor: To start a new session: To end a session: Administration Commands User Administration To create a user account: To remove a user account: To change a password: To set the access level privilege for a user: To grant or remove input status viewing privileges for a user: To display user access privilege levels: To grant serial port access to a user: To delete serial port access for a user: To display user serial port access: Serial Port Administration To create a port name: To set the serial port data-rate: To enable or disable active signal checking for serial connections: To display serial port information: System Administration To create a location description: To display system configuration information: To create a tower name: To display tower information: To create a infeed name: To display the firmware version: TCP/IP Administration To set the IP address: To set the subnet mask: To set the gateway IP address: To display network configuration information: HTTP Administration To enable or disable HTTP support: To change the HTTP port: To set the HTTP authentication method: Telnet Administration FTP Administration To set the FTP Host IP address: To set the FTP username: To set the FTP password: To set the FTP filename: SNTP Administration To set the SNTP server address: To display SNTP configuration information SSL SSH SNMP SSL SSL Command Summary Enabling and Setting up SSL Support To enable or disable SSL support: To change the access level: SSH SSH Command Summary Enabling and Setting up SSH Support To enable or disable SSH support: To change the SSH port: SNMP SNMP Command Summary Enabling and Setting up SNMP Support To enable SNMP support: To set the trap destination: To set the trap timer: To set the Setcomm community string: To set the Getcomm community string: To set the Trapcomm community string: To display SNMP configuration information: SNMP Traps Trap Summary Tower Status traps Infeed Status traps Environmental Monitor Status traps Temperature/Humidity Sensor Status traps Load traps Temp traps Humidity traps Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trap: To Enable or Disable a Load trap: To set the infeed load limit: To Enable or Disable a Change trap: To Enable or Disable the Temp trap: To set the Temperature threshold limits: To Enable or Disable the Humid trap: To set the Humidity threshold limits: To display trap information: RESETTING TO FACTORY DEFAULTS UPLOADING FIRMWARE TECHNICAL SPECIFICATIONS Resetting to Factory Defaults To reset to factory defaults from the HTML interface To reset to factory defaults from the command line To reset to factory defaults using the reset button Uploading Firmware Technical Specifications Models Europe/Asia Americas Power Ratings Physical Specifications Data Connections Branch Circuit Protection