Program Push Button, Upper Display | Miller Electric DS-74DX12

5-6. Program Push Button

1

2

Program

	1	Program Display
	The number of the active program
	is displayed.
	2	Program Push Button
	Press button to activate program
	select feature. To change the pro-
	gram number, press the Program
	push button and rotate the Adjust
	control.
	3	Program Push Button LED
3	The LED lights to indicate the Pro-
	gram push button is active.

5-7. Upper Display

.To set the correct voltage range for a particular power

source, see Section 4-13for power source selection menu, or Section 5-12for V-Min And V-Max adjustments.

1
4
Volts	Time (sec)

3

2

5

1 Upper Display

The upper display shows voltage or time. The unit displays both preset and actual arc voltage. When the unit is in a welding state, actual arc voltage is displayed. The upper display shows welding sequence time when the Time LED is illuminated.

2 Upper Display Push Button

Press and hold button to adjust or display weld time. Release button to display voltage.

3 Upper Display Push Button LED

The upper display push button LED illumi-

nates to indicate that information displayed can be changed by the Adjust control.

4Volts LED

5Time LED

The LEDs below the display illuminate to in- dicate which value is being shown.

At any time while welding, the unit permits the adjustment of the weld sequence voltage and overrides the display of actual arc volt- age.

•If the unit is displaying a welding sequence that can be timed, the welding time display mode is entered by pressing the upper dis-

play push button repeatedly until welding time is the active parameter in the upper display. At idle, the upper display toggles between showing weld voltage or weld time, with subsequent presses of the up- per display push button.

•The unit defaults to displaying welding voltage when a welding sequence display mode is first entered.

•If the weld sequence has a time set (as in spot time), after the weld program is com- pleted, ERR TRG 1 will be displayed to in- dicate the weld program is complete. Re- lease trigger to clear error.

OM-1500-14 Page 22

Image 26

Miller Electric DS-74DX12 Program Push Button, Upper Display, To set the correct voltage range for a particular power

Contents

Description OM-1500-14 207 499HProcesses File MIG Gmaw From Miller to You Table of Contents Options and Accessories Warranty Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burns Welding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyes Falling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injury EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical Devices Indique des instructions spécifiques Symboles utilisésUNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux Risque D’INCENDIE OU D’EXPLO- Sion LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesser LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-1500-14 Installing Swivel Into Pipe Post − InstallationSpecifications − Introduction Installing Control Box And Adjusting Tilt Installing Boom And Reel Support Installing Wire Guide Extension Exceed 100 PSI 689 kPa Equipment Connection DiagramShielding gas pressure not to Pin Information Control Box ConnectionsPin Plug Information Motor Speed Wire Type Wire Size Feed Speed Capability Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Gun Recommendation Table Slip at the feeder see pressure adjust Installing And Threading Welding WireAgainst surface. Tighten knob so wire Ment above. Cut wire off. Close cover DIP Switch S1 DIP Switch S4 Not For Customer Use Setting Internal DIP SwitchesWhen DIP switch positions are changed, Position Settings And Results For DIP Switch S1 Power Source Selection Menu − Operation Power SwitchLeft/Right Select Switch Operational Terms Time sec Jog/Purge SwitchFront Panel Controls Upper Display To set the correct voltage range for a particular powerProgram Push Button Setup Push Button Lower Display Sequence Push Button Adjust ControlWelding Sequence Diagram Start Weld Auxiliary Menus Burnback Trigger Hold SetupWire Feed Speed Units Trigger Program Select For more information on Sequence Push Button see Section − Setting Sequence ParametersSequence Parameters In a Program − Setting Dual Schedule Parameters Optional Dual Schedule Switch Diagrams Error Indications DiagnosticsError There is a two-position DIP Routine Maintenance − Maintenance & TroubleshootingDiagnostics For User Defined Options Months Trouble Remedy TroubleshootingDisconnect power before troubleshooting Pull − Electrical Diagram Circuit Diagram 204 144-C − Parts List 10-3 10-2 10-4 29 28 Optional Control Box Harness Connectors/Receptacles PLG117 165 Boom Assembly Boom Assembly -1Item Drive Assembly, Wire Drive Assembly, Wire -1Items 26 PLG5 Hardware is common Not available unless listed Roll Drive Roll and Wire Guide KitsFraction Metric Kit RollPage Start Your Professional Welding Career Now Page Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s